參數資料
型號: ISP1181BDGG
廠商: NXP SEMICONDUCTORS
元件分類: 總線控制器
英文描述: Full-speed Universal Serial Bus peripheral controller
中文描述: UNIVERSAL SERIAL BUS CONTROLLER, PDSO48
封裝: 6.10 MM, PLASTIC, MO-153, SOT-362-1, TSSOP-48
文件頁數: 61/70頁
文件大?。?/td> 341K
代理商: ISP1181BDGG
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
61 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
22.2 Interfacing ISP1181B with an H8S/2357 microcontroller
This section gives a summary of the ISP1181B interface with a H8S/2357 (or
compatible) microcontroller. Aspects discussed are: interrupt handling, address
mapping, DMA and I/O port usage for suspend and remote wake-up control. A typical
interface circuit is shown in
Figure 31
.
22.2.1
Interrupt handling
ISP1181B:
program the Hardware Configuration register to select an active LOW
level for output INT (INTPOL = 0, see
Table 20
)
H8S/2357
: program the IRQ Sense Control Register (ISCRH and ISCRL) to
specify low-level sensing for the IRQ input.
22.2.2
Address mapping in H8S/2357
The H8S/2357 bus controller partitions its 16 Mbyte address space into eight areas
(0 to 7) of 2 Mbyte each. The bus controller will activate one of the outputs CS0 to
CS7 when external address space for the associated area is accessed.
The ISP1181B can be mapped to any address area, allowing easy interfacing when
the ISP1181B is the only peripheral in that area. If in the example circuit for bus
configuration mode 0 (see
Figure 31
) the ISP1181B is mapped to address FFFF08H
(in area 7), output CS7 of the H8S/2357 can be directly connected to input CS of the
ISP1181B.
The external bus specifications, bus width, number of access states and number of
program wait states can be programmed for each address area. The recommended
settings of H8S/2357 for interfacing the ISP1181B are:
8-bit bus in Bus Width Control Register (ABWCR)
enable wait states in Access State Control Register (ASTCR)
1 program wait state in the Wait Control Register (WCRH and WCRL).
22.2.3
Using DMA
The ISP1181B can be configured for several methods of DMA with the H8S/2357 and
other devices. The interface circuit in
Figure 31
shows an example of the ISP1181B
working with the H8S/2357 in single-address DACK-only DMA mode. External
devices are not shown.
For single-address DACK-only mode, firmware must program the following settings:
ISP1181B
:
program the DMA Counter register with the total transfer byte count
program the Hardware Configuration Register to select active level LOW for
DREQ and DACK
select the target endpoint and transfer direction
select DACK-only mode and enable DMA transfer.
相關PDF資料
PDF描述
ISP1181 Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件)
ISP1181DGG INDUCTOR 4.7NH +-.3NH 0402 SMD
ISP1183 Low-power Universal Serial Bus interface device with DMA
ISP1183BS Low-power Universal Serial Bus interface device with DMA
ISP1301 Universal Serial Bus On-The-Go transceiver
相關代理商/技術參數
參數描述
ISP1181BDGG,112 功能描述:USB 接口集成電路 DO NOT USE ORDER -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BDGG,118 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1181BDGG-T 制造商:ST-Ericsson 功能描述:USB Peripheral Controller 48-Pin TSSOP T/R
ISP1181BDGGTM 功能描述:IC USB HOST CTRL FLL-SPD 48TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
ISP1181BPC 制造商:ST-Ericsson 功能描述:Full-Speed Universal Serial Bus Peripheral Controller