- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1181BDGG (NXP SEMICONDUCTORS) Full-speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1181BDGG |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Full-speed Universal Serial Bus peripheral controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PDSO48 |
| 封裝： | 6.10 MM, PLASTIC, MO-153, SOT-362-1, TSSOP-48 |
| 文件頁數： | 17/70頁 |
| 文件大?。?/td> | 341K |
| 代理商： | ISP1181BDGG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Philips Semiconductors
ISP1181B
Full-speed USB peripheral controller
Product data
Rev. 02 — 07 December 2004
17 of 70
9397 750 13958
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
The following example shows the steps which occur in a typical DMA transfer:
1. ISP1181B receives a data packet in one of its endpoint FIFOs; the packet must
be transferred to memory address 1234H.
2. ISP1181B asserts the DREQ signal requesting the 8237 for a DMA transfer.
3. The 8237 asks the CPU to release the bus by asserting the HRQ signal.
4. After completing the current instruction cycle, the CPU places the bus control
signals (MEMR, MEMW, IOR and IOW) and the address lines in three-state and
asserts HLDA to inform the 8237 that it has control of the bus.
5. The 8237 now sets its address lines to 1234H and activates the MEMW and IOR
control signals.
6. The 8237 asserts DACK to inform the ISP1181B that it will start a DMA transfer.
7. The ISP1181B now places the byte or word to be transferred on the data bus
lines, because its RD signal was asserted by the 8237.
8. The 8237 waits one DMA clock period and then de-asserts MEMW and IOR. This
latches and stores the byte or word at the desired memory location. It also
informs the ISP1181B that the data on the bus lines has been transferred.
9. The ISP1181B de-asserts the DREQ signal to indicate to the 8237 that DMA is
no longer needed. In
Single cycle mode
this is done after each byte or word, in
Burst mode
following the last transferred byte or word of the DMA cycle.
10. The 8237 de-asserts the DACK output indicating that the ISP1181B must stop
placing data on the bus.
11. The 8237 places the bus control signals (MEMR, MEMW, IOR and IOW) and the
address lines in three-state and de-asserts the HRQ signal, informing the CPU
that it has released the bus.
12. The CPU acknowledges control of the bus by de-asserting HLDA. After activating
the bus control lines (MEMR, MEMW, IOR and IOW) and the address lines, the
CPU resumes the execution of instructions.
For a typical bulk transfer the above process is repeated 64 times, once for each byte.
After each byte the address register in the DMA controller is incremented and the
byte counter is decremented. When using 16-bit DMA, the number of transfers is 32
and address incrementing and byte counter decrementing is done by 2 for each word.
10.3 DACK-only mode
The DACK-only DMA mode is selected by setting bit DAKOLY in the Hardware
Configuration Register (see
Table 20
). The pin functions for this mode are shown in
Table 9
. A typical example of ISP1181B in DACK-only DMA mode is given in
Figure 5
.
Table 9:
Symbol
DREQ
DACK
DACK-only mode: pin functions
Description
DMA request
DMA acknowledge
I/O
O
I
Function
ISP1181B requests a DMA transfer
DMA controller confirms the transfer;
also functions as data strobe
DMA controller terminates the transfer
not used
not used
EOT
RD
WR
End-Of-Transfer
read strobe
write strobe
I
I
I
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1181 | Full-speed Universal Serial Bus Interface Device(全速通用串行總線接口器件) |
| ISP1181DGG | INDUCTOR 4.7NH +-.3NH 0402 SMD |
| ISP1183 | Low-power Universal Serial Bus interface device with DMA |
| ISP1183BS | Low-power Universal Serial Bus interface device with DMA |
| ISP1301 | Universal Serial Bus On-The-Go transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1181BDGG,112 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BDGG,118 | 功能描述:USB 接口集成電路 USB 1.1 DEVICE CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1181BDGG-T | 制造商:ST-Ericsson 功能描述:USB Peripheral Controller 48-Pin TSSOP T/R |
| ISP1181BDGGTM | 功能描述:IC USB HOST CTRL FLL-SPD 48TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| ISP1181BPC | 制造商:ST-Ericsson 功能描述:Full-Speed Universal Serial Bus Peripheral Controller |
發布緊急采購，3分鐘左右您將得到回復。