- 您現在的位置：買賣IC網 > PDF目錄382773 > ZPSD611(V)E1 Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，零功耗，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) PDF資料下載
參數資料
| 型號： | ZPSD611(V)E1 |
| 英文描述： | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，零功耗，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| 中文描述： | 現場可編程微控制器外圍設備和嵌入式微-細胞（可編程邏輯，零功耗，4K的位的SRAM，26余個可編程輸入/輸出，通用PLD的有63個輸入） |
| 文件頁數： | 16/98頁 |
| 文件大?。?/td> | 484K |
| 代理商： | ZPSD611(V)E1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
ZPSD6XX(V) Family
12-16
The ZPLDs can minimize power consumption by switching off when inputs remain
unchanged for an extended time of about 70ns. Setting the Turbo mode bit to off (Bit 3 of
the PMMR0 register) automatically places the ZPLDs into standby if no inputs are changing.
Turbo off mode increases propagation delays while reducing power consumption. Refer to
the Power Management Unit on how to set up the Turbo Bit. Power is further reduced by the
PSDsoft development tools which disables unused product terms.
Each of the three ZPLDs has unique characteristics suited for its applications. They are
described in the following sections.
Decode PLD
The Decode PLD (DPLD), shown in Figure 5, is used to select the internal ZPSD6XX(V)
functions: EPROM blocks, SRAM, Registers (CSIOP) and the Port A Peripheral Mode.
All the select signals are active high and have one product term, except ES7 which has two.
The CSIOP is the select line for the ZPSD6XX(V) internal registers that occupies 256 bytes
of memory space. A second level decoder selects a register based on the address
inputs A[7-0].
Each EPROM block has its own chip select. The chip select of the eighth EPROM
block has two product terms, ES7A and ES7B. This allows the eighth block to reside
in two memory spaces, where ES7B can typically select reset vectors or configuration
bytes that are stored in the MCU address space.
PSEL 0 & 1 are used as inputs to Port A to control the port’s Peripheral I/O mode
operation. Usually PSEL 0&1 are defined in term of the MCU address inputs. This mode is
explained in the I/O Port section.
ZPLDs
(cont.)
Input Source
Input Name
Number of Bits
MCU Address Bus
A[15:0]
*
16
I/O Ports A, B, and C
PA[7:0], PB[7:0]
PC[7:3], PC[1:0]
23
Page Register
PGR[3:0]
4
Control Signal
CNTL1 (Read)
1
Reset Pin
RESET
1
Table 7. DPLD Inputs
*
NOTE:
The address inputs are A[19:4] in 80C51XA mode, A[3:0] are assigned to Port A.
相關PDF資料 |
PDF描述 |
|---|---|
| ZPSD612(V)E1 | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，零功耗，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| ZPSD613(V)E1 | Field Programmable Microcontroller Peripherals with Embedded Micro--Cell(可編程邏輯，零功耗，4K位SRAM,26個可編程I/O,通用PLD有63個輸入) |
| ZPSD813F1V | Flash In System Programmable Mirocomputer Peripherals(閃速，在系統可編程微控制器外圍器件，1M位閃速存儲器，256K位EEPROM，16K位SRAM) |
| ZR33771GC-40 | Cell Rectifier Diodes |
| ZR33771GM-20 | Cell Rectifier Diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ZPSD612E1-15L | 制造商:WSI 功能描述: |
| ZPSD612E1V-20L | 制造商:WSI 功能描述: |
| ZPSD613E1-15J | 制造商:WSI 功能描述: |
| ZPSD613E1-15L | 制造商:WSI 功能描述: |
| ZPSD613E1-70J | 制造商:WSI 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。