REV. 1.2.2 UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART 43 ] ISR[0]: Interrupt Status Logic " />
參數資料
型號： XR17D158IV-F
廠商： Exar Corporation
文件頁數： 38/73頁
文件大小： 0K
描述： IC UART PCI BUS OCTAL 144LQFP
產品培訓模塊： UART Product Overview
標準包裝： 60
特點： *
通道數： 8
FIFO's： 64 字節
規程： RS485
電源電壓： 3.3V，5V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP
供應商設備封裝： 144-LQFP（20x20）
包裝： 托盤
其它名稱： 1016-1292
xr
XR17D158
REV. 1.2.2
UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART
43
]
ISR[0]: Interrupt Status
Logic 0 = An interrupt is pending and the ISR contents may be used as a pointer to the appropriate interrupt
service routine.
Logic 1 = No interrupt pending (default condition).
ISR[3:1]: Interrupt Status
These bits indicate the source for a pending interrupt at interrupt priority levels 1, 2, 3 and 4 (See Interrupt
Source Table 14).
ISR[4]: Xoff/Xon or Special Character Interrupt Status
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-4 indicates that the receiver detected a data match
of the Xoff character(s). If this is an Xoff/Xon interrupt, it can be cleared by a read to the ISR. Reading the
XCHAR register will indicate which character (Xoff or Xon) was received last. If it is a special character
interrupt, it can be cleared by reading ISR or it will automatically clear after the next character is received.
ISR[5]: RTS#/CTS# Interrupt Status
This bit is enabled when EFR bit-4 is set to a logic 1. ISR bit-5 indicates that the CTS# or RTS# has changed
state from LOW to HIGH.
ISR[7:6]: FIFO Enable Status
These bits are set to a logic 0 when the FIFOs are disabled. They are set to a logic 1 when the FIFOs are
enabled.
5.8.6
FIFO Control Register (FCR) - Write-Only
This register is used to enable the FIFOs, clear the FIFOs, set the transmit/receive FIFO trigger levels, and
select the DMA mode (legacy term that refers to "block transfer mode"). The DMA and FIFO modes are
defined as follows:
FCR[0]: TX and RX FIFO Enable
Logic 0 = Disable the transmit and receive FIFO (default).
Logic 1 = Enable the transmit and receive FIFOs. This bit must be set to logic 1 when other FCR bits are
written or they will not be programmed.
FCR[1]: RX FIFO Reset
This bit is only active when FCR bit-0 is active.
Logic 0 = No receive FIFO reset (default).
Logic 1 = Reset the receive FIFO pointers and FIFO level counter logic (the receive shift register is not
cleared or altered). This bit will return to a logic 0 after resetting the FIFO.
TABLE 14: INTERRUPT SOURCE AND PRIORITY LEVEL
PRIORITY
ISR REGISTER STATUS BITS
SOURCE OF THE INTERRUPT
LEVEL
BIT-5
BIT-4
BIT-3
BIT-2
BIT-1
BIT-0
1
0
1
0
LSR (Receiver Line Status Register)
2
0
1
0
RXRDY (Received Data Ready)
3
0
1
0
RXRDY (Receive Data Time-out)
4
0
1
0
TXRDY (Transmitter Holding Register Empty)
5
0
MSR (Modem Status Register)
6
0
1
0
RXRDY (Received Xon/Xoff or Special character)
7
1
0
CTS#/DSR#, RTS#/DTR# change of state
X
0
1
None (default)
相關PDF資料
PDF描述
XR17V252IM IC UART PCI BUS DUAL 100TQFP
XR17V254IV-F IC UART PCI BUS QUAD 144LQFP
XR17V258IV-F IC UART PCI BUS OCTAL 144LQFP
XR17V352IB113-F IC UART PCIE 256B DUAL 113FPBGA
XR17V354IB176-F IC UART PCIE 256B QUAD 176FPBGA
相關代理商/技術參數
參數描述
XR17D158IVTR-F 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17D158IVTR-F
XR17L152 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART
XR17L152CM 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART
XR17L152IM 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART
XR17L154 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*