REV. 1.2.2 UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART 41 5.8.4 Interrupt Enable Register (IER) - Read/Write The Interrupt Enable Re" />
參數資料
型號： XR17D158IV-F
廠商： Exar Corporation
文件頁數： 36/73頁
文件大?。?/td> 0K
描述： IC UART PCI BUS OCTAL 144LQFP
產品培訓模塊： UART Product Overview
標準包裝： 60
特點： *
通道數： 8
FIFO's： 64 字節
規程： RS485
電源電壓： 3.3V，5V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP
供應商設備封裝： 144-LQFP（20x20）
包裝： 托盤
其它名稱： 1016-1292
xr
XR17D158
REV. 1.2.2
UNIVERSAL (3.3V AND 5V) PCI BUS OCTAL UART
41
5.8.4
Interrupt Enable Register (IER) - Read/Write
The Interrupt Enable Register (IER) masks the interrupts from receive data ready, transmit empty, line status
and modem status registers. These interrupts are reported in the Interrupt Status Register (ISR) register and
also encoded in INT (INT0-INT3) register in the Device Configuration Registers.
IER VERSUS RECEIVE FIFO INTERRUPT MODE OPERATION
When the receive FIFO (FCR bit-0 = a logic 1) and receive interrupts (IER BIT-0 = logic 1) are enabled, the
RHR interrupts (see ISR bits 3 and 4) status will reflect the following:
A. The receive data available interrupts are issued to the host when the FIFO has reached the programmed
trigger level. It will be cleared when the FIFO drops below the programmed trigger level.
B. FIFO level will be reflected in the ISR register when the FIFO trigger level is reached. Both the ISR register
status bit and the interrupt will be cleared when the FIFO drops below the trigger level.
C. The receive data ready bit (LSR BIT-0) is set as soon as a character is transferred from the shift register to
the receive FIFO. It is reset when the FIFO is empty.
IER VERSUS RECEIVE/TRANSMIT FIFO POLLED MODE OPERATION
When FCR BIT-0 equals a logic 1 for FIFO enable, resetting IER bits 0-3 enables the 158 in the FIFO polled
mode of operation. Since the receiver and transmitter have separate bits in the LSR either or both can be used
in the polled mode by selecting respective transmit or receive control bit(s).
A. LSR BIT-0 indicates there is data in RHR or RX FIFO.
B. LSR BIT-1 indicates an overrun error has occurred and that data in the FIFO may not be valid.
C. LSR BITS 2-4 provides the type of receive data errors encountered for the data byte in RHR, if any.
D. LSR BIT-5 indicates THR is empty.
E. LSR BIT-6 indicates when both the transmit FIFO and TSR are empty.
F. LSR BIT-7 indicates a data error in at least one character in the RX FIFO.
IER[0]: RHR Interrupt Enable
The receive data ready interrupt will be issued when RHR has a data character in the non-FIFO mode or when
the receive FIFO has reached the programmed trigger level in the FIFO mode. A receive data timeout interrupt
will be issued in the FIFO mode when the receive FIFO has not reached the programmed trigger level and the
RX input has been idle for 4 character + 12 bit times.
Logic 0 = Disable the receive data ready interrupt (default).
Logic 1 = Enable the receiver data ready interrupt.
IER[1]: THR Interrupt Enable
When Auto RS485 mode operation is disabled (FCTR bit-5 = 0), this interrupt is associated with bit-5 in the
LSR register. An interrupt is issued whenever the THR becomes empty or when data in the FIFO falls below
the programmed trigger level. When Auto RS485 mode operation is enabled (FCTR bit-5 = 1), this interrupt is
associated with bit-6 in the LSR register. An interrupt is issued whenever the TX FIFO and the TSR becomes
empty.
Logic 0 = Disable Transmit Holding Register empty interrupt (default).
Logic 1 = Enable Transmit Holding Register empty interrupt.
IER[2]: Receive Line Status Interrupt Enable
Any of LSR register bits 1, 2, 3 or 4 will generate an LSR interrupt immediately when a character received by
the RX FIFO has an error.
Logic 0 = Disable the receiver line status interrupt (default).
Logic 1 = Enable the receiver line status interrupt.
IER[3]: Modem Status Interrupt Enable
Logic 0 = Disable the modem status register interrupt (default).
Logic 1 = Enable the modem status register interrupt.
相關PDF資料
PDF描述
XR17V252IM IC UART PCI BUS DUAL 100TQFP
XR17V254IV-F IC UART PCI BUS QUAD 144LQFP
XR17V258IV-F IC UART PCI BUS OCTAL 144LQFP
XR17V352IB113-F IC UART PCIE 256B DUAL 113FPBGA
XR17V354IB176-F IC UART PCIE 256B QUAD 176FPBGA
相關代理商/技術參數
參數描述
XR17D158IVTR-F 制造商:Exar Corporation 功能描述:UART 8-CH 64Byte FIFO 5V 144-Pin LQFP T/R 制造商:Exar Corporation 功能描述:XR17D158IVTR-F
XR17L152 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART
XR17L152CM 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART
XR17L152IM 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS DUAL UART
XR17L154 制造商:EXAR 制造商全稱:EXAR 功能描述:3.3V PCI BUS QUAD UART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*