參數資料
型號： USB97CFDC-MN
廠商： STANDARD MICROSYSTEMS CORP
元件分類： 存儲控制器/管理單元
英文描述： USB FLOPPY DISK CONTROLLER
中文描述： 1 Mbps, FLOPPY DISK DRIVE CONTROLLER, PQFP100
封裝： 12 X 12 MM, TQFP-100
文件頁數： 50/59頁
文件大小： 385K
代理商： USB97CFDC-MN
SMSC DS – USB97C201
Page 50
Rev. 03/25/2002
PRELIMINARY
2. Endpoint 2 will be receiving more data (short packet, ie end of file segment) followed by a OUT packet from the
host on the control endpoint (EP0) requesting data. Data has already been placed in the SRAM EP0 TX Buffer,
its length loaded into the
EP0TX_BC
register, and the TX bit of the EP0TX_CTL register written to a “1”.
Phase 0 (0) will refer the 60MHz sub-period that the SIE has access to the SRAM, while 1 will be that for the ATA
interface and 2 will be for the 8051 (3 is idle and reserved).
During one of the 0 periods, the SIE finishes loading the last of the packet data into the B buffer. RAMWR_B
interrupt bit is set notifying firmware of completion of packet. Assuming that the RAMWR_A=0 (the data in the A
SRAM buffer has been previously transferred), the RAMWR_TOGGLE bit is written to a “0” by the firmware, which
clears the RAMWRBC_A1/2 registers and directs the next data received from EP2 to the A buffer space in SRAM.
Firmware reads RAMWRBC_B1/2 to determine packet size, loads value into RAMRDBC_B1/2 register. The
RAMRD_TOGGLE bit of EP2_CTL is written by the firmware with a “1” which will begin the transfer of the B buffer to
ATA interface on the next 1 period.
On subsequent slices, the next DWORD of the incoming data packet from the host is loaded into the A buffer space
on 0 from the SIE, auto-incrementing the RAMWRBC_A1/2 register values. On 1 slices, the data from the B
buffer space is output to the ATA interface (appropriately flow controlled by that interface), and incrementing a
counter which is compared to the RAMRDBC_B1/2 registers to determine if the transfer is completed. During this
time, the SIE receives an IN on EP0. During the next 0 periods, and until the final transmission of the packet data
to the SIE is completed, data is read from the SRAM into the SIE for EP0 in response to INs. The writing of the A
buffer by the SIE on 0 periods will then resume with the reception of OUTs on EP2.
Assuming the incoming data completes loading into the A buffer space, before the B buffer is transferred to the ATA
interface, the RAMWR_A interrupt will be generated before the RAMRD_B interrupt. The firmware will then wait until
the RAMRD_B interrupt occurs, loads the RAMRDBC_A1/2 register with the count from the RAMWRBC
_
A1/2
registers, flips the buffers (ie RAMRD_TOGGLE=0, RAMWR_TOGGLE=1), and clears the RAMWR_B bit (allowing
the reuse of the B buffer area).
On subsequent 0 slices, the SIE will read (for IN tokens) or write (for OUT tokens) the appropriate SRAM buffer
according to which EP is being accessed, if any, while the USB97C201 transfers the A buffer to the ATA interface
during 1. When an OUT packet on EP0 is received, the data in the SRAM will be transferred to the SIE on
subsequent 0 slices, DWORD at a time until completed.
6.9 EP2 Automatic Buffer Operations
Automatic operation of the interleaved SRAM buffers exists in two degrees: Automatic toggling of input buffers and
automatic transfer of input and output buffer data to/from the SIE and ATA interface. These features may be disabled
via bits in the ATA_CTL register.
6.9.1
If the AUTO_TOG bit of the ATA_CTL register is set to a “1”, then receive auto-toggling between the A and B buffers
for writes to the SRAM is enabled. Figure 3 illustrates the auto-toggle of the receive buffers.
RECEIVE AUTO-TOGGLE
相關PDF資料
PDF描述
USB97C202 ATA/ATAPI CONTROLLER
USB97C202-MN-02 ATA/ATAPI CONTROLLER
USB97C223 capacitor Selection for Internal Regulator Output Pins
USB97C243 capacitor Selection for Internal Regulator Output Pins
USB97CFDC USB FLOPPY DISK CONTROLLER
相關代理商/技術參數
參數描述
USB-A(M)-A(F)-1M-BEIGE 制造商:SMART CABLE 功能描述:
USB-A-001A 制造商:YAMAICHI 制造商全稱:Yamaichi Electronics Co., Ltd. 功能描述:Universal Serial Bus, Type A - 90° Receptacle
USB-A-001A-30 制造商:YAMAICHI 制造商全稱:Yamaichi Electronics Co., Ltd. 功能描述:Universal Serial Bus, Type A - 90° Receptacle
USB-A-002A 制造商:YAMAICHI 制造商全稱:Yamaichi Electronics Co., Ltd. 功能描述:Universal Serial Bus, Type A - 90° Receptacle
USB-A-002A-30 制造商:YAMAICHI 制造商全稱:Yamaichi Electronics Co., Ltd. 功能描述:Universal Serial Bus, Type A - 90° Receptacle
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*