參數資料
型號: TMP86FH09NG
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PDIP32
封裝: 0.400 INCH, 1.78 MM PITCH, LEAD FREE, PLASTIC, SDIP-32
文件頁數: 38/154頁
文件大小: 1433K
代理商: TMP86FH09NG
Page 122
12. 10-bit AD Converter (ADC)
12.2 Register configuration
TMP86CH09NG
12.2 Register configuration
The AD converter consists of the following four registers:
1. AD converter control register 1 (ADCCR1)
This register selects the analog channels and operation mode (Software start or repeat) in which to per-
form AD conversion and controls the AD converter as it starts operating.
2. AD converter control register 2 (ADCCR2)
This register selects the AD conversion time and controls the connection of the DA converter (Ladder
resistor network).
3. AD converted value register 1 (ADCDR1)
This register used to store the digital value fter being converted by the AD converter.
4. AD converted value register 2 (ADCDR2)
This register monitors the operating status of the AD converter.
Note 1: Select analog input channel during AD converter stops (ADCDR2<ADBF> = "0").
Note 2: When the analog input channel is all use disabling, the ADCCR1<AINDS> should be set to "1".
Note 3: During conversion, Do not perform port output instruction to maintain a precision for all of the pins because analog input
port use as general input port. And for port near to analog input, Do not input intense signaling of change.
Note 4: The ADCCR1<ADRS> is automatically cleared to "0" after starting conversion.
Note 5: Do not set ADCCR1<ADRS> newly again during AD conversion. Before setting ADCCR1<ADRS> newly again, check
ADCDR2<EOCF> to see that the conversion is completed or wait until the interrupt signal (INTADC) is generated (e.g.,
interrupt handling routine).
Note 6: After STOP or SLOW/SLEEP mode are started, AD converter control register1 (ADCCR1) is all initialized and no data can
be written in this register. Therfore, to use AD converter again, set the ADCCR1 newly after returning to NORMAL1 or
NORMAL2 mode.
AD Converter Control Register 1
ADCCR1
(000EH)
765
43210
ADRS
AMD
AINDS
SAIN
(Initial value: 0001 0000)
ADRS
AD conversion start
0:
1:
-
AD conversion start
R/W
AMD
AD operating mode
00:
01:
10:
11:
AD operation disable
Software start mode
Reserved
Repeat mode
AINDS
Analog input control
0:
1:
Analog input enable
Analog input disable
SAIN
Analog input channel select
0000:
0001:
0010:
0011:
0100:
0101:
0110:
0111:
1000:
1001:
1010:
1011:
1100:
1101:
1110:
1111:
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
Reserved
相關PDF資料
PDF描述
TMP86FS49BUG 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
TMP86PS25F 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100
TMP87C800N 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
TMP89FH46LDUG 8-BIT, FLASH, MICROCONTROLLER, PQFP48
TMP89FM42UG 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
TMP86FH09NG(ZM) 功能描述:8位微控制器 -MCU TLCS870/C 16K FLASH RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
TMP86FH12MG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 16KB FLASH 5V 30SSOP - Bulk 制造商:Toshiba America Electronic Components 功能描述:8BIT MCU 16K FLASH 512B RAM 86FH12
TMP86FH12MG(Z) 功能描述:8位微控制器 -MCU 16k Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
TMP86FH46ANG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 16KB FLASH 5V 42PIN SDIP - Bulk
TMP86FH46ANG(Z) 功能描述:8位微控制器 -MCU 16K Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT