參數資料
型號： SAA7708H
廠商： NXP Semiconductors N.V.
元件分類： 數字信號處理
英文描述： Car Radio Digital Signal Processor
中文描述： 汽車無線電數字信號處理器
文件頁數： 14/60頁
文件大小： 281K
代理商： SAA7708H
1998 May 19
14
Philips Semiconductors
Preliminary specification
Car Radio Digital Signal Processor
SAA7708H
10 FUNCTIONAL DESCRIPTION
10.1
Signal path for Level information
For FM weak signal processing, for AM and FM purposes (absolute level and multipath) a FM/AM Level input is
implemented (pin LEVEL). In the case of radio reception the clocking of the filters and the AD is based on a 38 kHz Fs
frequency. A DC input signal is converted by a bitstream first order Sigma-Delta AD converter followed by a decimation
filter.
The input signal has to be obtained from a radio part. The tuner must deliver the level information of either AM or FM to
the LEVEL pin.
10.1.1
T
HE
VREFAD
PIN
Via this pin the Midref voltage of the AD’s is filtered. This Midref voltage is used as reference of the LEVEL AD and half
supply reference of the two third order switch capacitor ADs. External capacitors (connected to VSSA1) prevents
crosstalk between the AD’s. This pin must also used in the application as reference for the inputs AM/AM_R, AM_L, ,
TAPE_L and TAPE_R (see Fig. 21).
10.2
Signal path of the third order switched capacitor AD’s.
10.2.1
T
HE
FM MPX
SIGNAL PATH
The CDSP has in total three analog audio source channels. One of the analog inputs is the FM_MPX signal. Selection
of this signal is achieved according Table 3. The multiplex FM signal is converted to the digital domain in SCAD1, a
bitstream third order switched capacitor AD converter. A decimation filter reduces the output of the AD to a lower sample
rate. From this filter the following signals are derived and are processed in the DSP.
The outputs from this signal path to the DSP which are all running on a sample frequency of 38 kHz are:
Pilot presence indication: Pilot-I. This one bit signal is low for a pilot frequency deviation < 3 kHz and high for a pilot
frequency deviation > 3 kHz AND the FM MPX stereodecoder is locked on a pilot tone.
‘Left’ and ‘Right’ FM reception stereo signal: This is the 18 bit output of the stereo decoder after the matrix decoding
in ISN I
2
S format.This signal is fed via a muxer to a general I
2
S interface block that communicates with the DSP.
A noise level information. This signal is derived from the first MPX decimation fiter via a wide band noise filter.
Detection is done with an envelope detector. This noise level is filtered in the DSP core and is used to optimize the FM
weak signal processing.
Normally the FM_MPX input and the FM_RDS input have the same source. If the FM input contains a stereo radio
channel, the pilot information is used to lock the clocking of the decimation filters of FM MPX and RDS path and also the
stereo decoder.
10.2.2
I
NPUT SENSITIVITY FOR
FM
AND
RDS
The FM and RDS input sensitivity is designed for tuner front ends which deliver an output voltage of 200 mVrms at a
modulation depth of 22.5 kHz of a 1 kHz tone. In this case the I
2
C bit pcs_ad_sel must be ‘o’ and the SEL_FR switch is
also low. The MPX part of the FM_MPX signal will be processed via SCAD1, the RDS part is processed via SCAD2..
Another input sensitivity can be obtained by putting the pcs_ad_sel bit high. Biasing of this input must now take place
exterenally via high-ohmic resistors connected to the VREFAD pin. In this case the input sensitivity has increased from
200 mVrms to 65 mVrms at modulation depth of 22.5 kHz. Reduction of the input sensitivity can be obtained by an
external resistor tap consisting of an in the signal path placed series resistor and a resistor to VREFAD.
10.2.3
T
HE SIGNAL FLOW OF THE
AM, CD
ANALOG AND
TAPE
The signal AM mono via the AM/AM_R input can be selected by the correct values of the I
2
C bits. There is also an option
available to connect a left and right signal to the chip. This can be for instance the AM-Right and AM-Left signal. The AM,
TAPE and CD inputs are buffered by an opamp to ensure a high ohmic input that makes external signal reduction
相關PDF資料
PDF描述
SAL175UF-A HERMETIC ULTRAFAST DIODE
SAL200UF-A HERMETIC ULTRAFAST DIODE
SAL225UF-A HERMETIC ULTRAFAST DIODE
SAL250UF-A HERMETIC ULTRAFAST DIODE
SAL175UF3A HERMETIC ULTRAFAST DIODE
相關代理商/技術參數
參數描述
SAA7709/N107 制造商:PHILIPS-SEMI 功能描述:
SAA7709H/N103 功能描述:音頻 DSP DIGITAL SIGNAL PROCESSOR RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
SAA7709H/N103,518 功能描述:音頻 DSP DIRAC-2 RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
SAA7709H/N103,557 功能描述:音頻 DSP DIGITAL SIGNAL RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
SAA7709H/N103/S420 功能描述:音頻 DSP Car radio Digital Signal Processor RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*