- 您現在的位置：買賣IC網 > PDF目錄98068 > S1C62920D 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC63 PDF資料下載
參數資料
| 型號： | S1C62920D |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, MROM, 1.3 MHz, MICROCONTROLLER, UUC63 |
| 封裝： | DIE-63 |
| 文件頁數： | 27/78頁 |
| 文件大?。?/td> | 874K |
| 代理商： | S1C62920D |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁
S1C62920 TECHNICAL MANUAL
EPSON
25
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (I/O Ports)
4.6.4 Control of I/O ports
Table 4.6.4.1 lists the I/O ports' control bits and their addresses.
Table 4.6.4.1 Control bits of I/O ports
Address
Comment
Register
D3
D2
D1
D0
Name
Init
1
0
*1
IOC00
P00
IOC10
P10
ESIF
IOC03
IOC02
IOC01
IOC00
P03
P02
P01
P00
IOC13
IOC12
IOC11
IOC10
P13
P12
P11
P10
SCS0
0
SCTRG(W)
SCTRG(R)
ESIF
*5
0
1
0
1
0
–
0
Output
High
Output
High
FOUT
Trigger
Run
SIF port
Input
Low
Input
Low
Slave
–
Stop
I/O port
IOC01
P01
IOC11
P11
SCTRG
IOC02
P02
IOC12
P12
0
R
IOC03
P03
IOC13
P13
SCS0
R/W
B0H
B2H
B4H
B6H
E8H
*2
*7
I/O control register (P00–P03)
I/O port P00–P03
I/O control register (P10–P13)
I/O port P10–P13
Serial I/F clock mode selection
Unused
Serial I/F clock trigger (writing)
Serial I/F clock status (reading)
P1 port function selection
R/W
*1 Initial value at the time of initial reset
*5 Constantly "0" when being read
*2 Not set in the circuit
*6 Refer to main manual
*3 Undefined
*7 Page switching in I/O memory is not necessary
*4 Reset (0) immediately after being read
(1) Function selection for ports
ESIF: Serial interface enable (E8HD0)
Selects function for P10–P13.
When "1" is written:
Serial interface input/output port
When "0" is written:
I/O port
Reading:
Valid
When the serial interface is used, write "1" to this register and when P10–P13 are used as I/O port, write
"0". The configuration of the terminals within P10–P13 that are used for the serial interface is decided by the
mode selected with the SCS0 register.
At initial reset, this register is set to "0".
(2) I/O port control
P00–P03, P10–P13: I/O port data (B2H, B6H)
I/O port data can be read and output data can be set through these ports.
When writing data
When "1" is written:
High level
When "0" is written:
Low level
When an I/O port is set to the output mode, the written data is output unchanged from the I/O port
terminal. When "1" is written as the port data, the port terminal goes high (VDD), and when "0" is written,
the level goes low (VSS).
Port data can be written also in the input mode.
相關PDF資料 |
PDF描述 |
|---|---|
| S1C62A33D | 4-BIT, MROM, 0.6 MHz, MICROCONTROLLER, UUC86 |
| S1C62N82F | 4-BIT, MROM, 0.032 MHz, MICROCONTROLLER, PQFP80 |
| S1C63158F0A0100 | 4-BIT, FLASH, 4.2 MHz, MICROCONTROLLER, PQFP100 |
| S1C63358F0A0100 | 4-BIT, MROM, 4.1 MHz, MICROCONTROLLER, PQFP100 |
| S1C63406F | 4-BIT, MROM, 4.2 MHz, MICROCONTROLLER, PQFP128 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S1C63004 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63008 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63016 | 制造商:EPSON 制造商全稱:EPSON 功能描述:CMOS 4-bit Single Chip Microcontroller |
| S1C63158 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
| S1C63408 | 制造商:EPSON 制造商全稱:EPSON 功能描述:4-bit Single Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。