參數資料
型號： MT9046
廠商： Zarlink Semiconductor Inc.
元件分類： 基準電壓源/電流源
英文描述： T1/E1 System Synchronizer with Holdover
中文描述： T1/E1的系統同步的緩繳暫繳稅
文件頁數： 7/34頁
文件大?。?/td> 508K
代理商： MT9046
MT9046
Data Sheet
7
Zarlink Semiconductor Inc.
Phase Detector
- the Phase Detector compares the virtual reference signal from the TIE Corrector circuit with the
feedback signal from the Frequency Select MUX circuit, and provides an error signal corresponding to the phase
difference between the two. This error signal is passed to the Limiter circuit. The Frequency Select MUX allows the
proper feedback signal to be externally selected (e.g., 8 kHz, 1.544 MHz, 2.048 MHz or 19.44 MHz).
Figure 4 - DPLL Block Diagram
Limiter
- the Limiter receives the error signal from the Phase Detector and ensures that the DPLL responds to all
input transient conditions with a maximum output phase slope of 5 ns per 125 us. This is well within the maximum
phase slope of 7.6 ns per 125 us or 81 ns per 1.326 ms specified by AT&T TR62411 and Bellcore GR-1244-CORE,
respectively.
Loop Filter
- the Loop Filter is similar to a first order low pass filter with a 1.9 Hz cutoff frequency for all four
reference frequency selections (8 kHz, 1.544 MHz, 2.048 MHz or 19.44 MHz). This filter ensures that the jitter
transfer requirements in ETS 300 011 and AT&T TR62411 are met.
Control Circuit
- the Control Circuit uses status and control information from the State Machine and the Input
Impairment Circuit to set the mode of the DPLL. The three possible modes are Normal, Holdover and Freerun.
Digitally Controlled Oscillator (DCO)
- the DCO receives the limited and filtered signal from the Loop Filter, and
based on its value, generates a corresponding digital output signal. The synchronization method of the DCO is
dependent on the state of the MT9046.
In Normal Mode, the DCO provides an output signal which is frequency and phase locked to the selected input
reference signal.
In Holdover Mode, the DCO is free running at a frequency equal to the last (less 30 ms to 60 ms) frequency the
DCO was generating while in Normal Mode.
In Freerun Mode, the DCO is free running with an accuracy equal to the accuracy of the OSCi 20 MHz source.
Lock Indicator - If the PLL is in frequency lock (frequency lock means the center frequency of the PLL is identical to
the line frequency), and the input phase offset is small enough such that no phase slope limiting is exhibited, then
the lock signal will be set high. For specific Lock Indicator design recommendations see the Applications - Lock
Indicator section.
Output Interface Circuit
The output of the DCO (DPLL) is used by the Output Interface Circuit to provide the output signals shown in Figure
5. The Output Interface Circuit uses four Tapped Delay Lines followed by a T1 Divider Circuit, an E1 Divider Circuit,
and a DS2 Divider Circuit to generate the required output signals.
Four tapped delay lines are used to generate 16.384 MHz, 12.352 MHz, 12.624 MHz and 19.44 MHz signals.
Control
Circuit
State Select
from
Input Impairment Monitor
State Select
from
State Machine
Feedback Signal
from
Frequency Select MUX
DPLL Reference
to
Output Interface Circuit
Virtual Reference
from
TIE Corrector
Limiter
Loop Filter
Digitally
Controlled
Oscillator
Phase
Detector
相關PDF資料
PDF描述
MT9046AN T1/E1 System Synchronizer with Holdover
MT90503 2048VC AAL1 SAR
MT90503AG CLIP, STRAIN RELIEF, 50WAY; For use with:820 Series Tripolarized Wiremount Sockets; Ways, No. of:50; Material:Metal; Connector type:Strain Relief RoHS Compliant: Yes
MT90520 8-Port Primary Rate Circuit Emulation AAL1 SAR
MT90520AG 8-Port Primary Rate Circuit Emulation AAL1 SAR
相關代理商/技術參數
參數描述
MT9046AN 制造商:Microsemi Corporation 功能描述:
MT9046AN1 制造商:Microsemi Corporation 功能描述:FRAMER E1 /T1 3.3V 48SSOP - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 48SSOP 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 48SSOP
MT9046ANR1 制造商:Microsemi Corporation 功能描述:FRAMER E1 /T1 3.3V 48SSOP - Tape and Reel 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 48SSOP 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 48SSOP
MT9048 制造商:DBLECTRO 制造商全稱:DB Lectro Inc 功能描述:Standard Type
MT90489 制造商: 功能描述: 制造商:undefined 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*