- 您現在的位置：買賣IC網 > PDF目錄98005 > M34551E8-XXXFP 4-BIT, OTPROM, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M34551E8-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 10 MM, 0.65 MM PITCH, PLASTIC, QFP-48 |
| 文件頁數： | 83/154頁 |
| 文件大?。?/td> | 1778K |
| 代理商： | M34551E8-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁
FUNCTIONAL BLOCK OPERATIONS
4551 Group User’s Manual
HARDWARE
1-23
(2) Precautions
Note the following for the use of timers.
q Prescaler
Stop the prescaler operation to change its frequency
dividing ratio.
q Count source
Stop timer 1 or timer LC counting to change its count
source. When timer 2 count source changes from f(XCIN)
to ORCLK (W23 = “0”
→ W23 = “1”), the count value of
timer 2 is initialized. However, when timer 2 count source
changes from ORCLK to f(XCIN) (W23 = “1”
→ W23 = “0”)
or the same count source is set again (W23 = “0”
→ W23
= “0” or W23 = “1”
→ W23 = “1”), the count value of timer
2 is not initialized.
q Timer 2
Timer 2 has the watchdog timer function (WDT). When
timer 2 is used as the WDT, note that the processing to
initialize the count value and the execution of the WRST
instruction.
q Reading the count value
Stop the prescaler and then execute the TAB1 instruction
to read timer 1 data.
q Writing to reload register R1
When writing data to reload register R1 while timer 1 is
operating, avoid a timing when timer 1 underflows.
(3) Prescaler
Prescaler is a frequency divider. Its frequency dividing ratio
can be selected. The count source of prescaler is the
instruction clock (INSTCK).
Use the bit 2 of register W1 to select the prescaler dividing
ratio and the bit 3 to start and stop its operation. When the bit
3 of register W1 is cleared to “0,” prescaler is initialized, and
the output signal (ORCLK) stops.
(4) Timer 1 (interrupt function)
Timer 1 is an 8-bit binary down counter with the timer 1 reload
register (R1). When timer 1 stops, data can be set
simultaneously in timer 1 and the reload register (R1) with
the T1AB instruction. When timer 1 is operating, data can be
set only in the reload register (R1) with the T1AB instruction.
When setting the next count data to reload register R1 while
timer 1 is operating, be sure to set data before timer 1
underflows.
Timer 1 starts counting after the following process;
set data in timer 1,
select the count source with bits 0 and 1 of register W1,
set the bit 0 of register W2 to “1.”
Once count is started, when timer 1 underflows (the next count
pulse is input after the contents of timer 1 becomes “0”), the
timer 1 interrupt request flag (T1F) is set to “1,” new data is
loaded from reload register R1, and count continues (auto-
reload function).
When a value set in reload register R1 is n, timer 1 divides
the count source signal by n + 1 (n = 0 to 255).
Data can be read from timer 1 to registers A and B. Stop
counting and then execute the TAB1 instruction to read its
data.
(5) Timer 2 (interrupt function)
Timer 2 is a 14-bit binary down counter.
Timer 2 starts counting after the following process;
select the count source with the bit 3 of register W2, and
the clock as a count source is supplied.
Timer 2 stops counting and its count value is retained when
supply of a clock as a count source stops. Timer 2 is initialized
at reset and when the count source changes from f(XCIN)
(W23=“0”) to ORCLK (W23=“1”).
The count value to set the timer 2 interrupt request flag (T2F)
to “1” can be selected from every 8192 count or every 16384
count with bits 1 and 2 of register W2. The count source signal
divided by 16 is output from timer 2.
Timer 2 can be used as a counter for clock in the clock
operating mode (POF instruction executed).
(6) Timer LC
Timer LC is a 4-bit binary down counter with the timer LC
reload register (RLC). Data can be set simultaneously in timer
LC and the reload register (RLC) with the TLCA instruction.
Timer LC starts counting after the following process;
set data in timer LC,
select the count source with the bit 1 of register W3,
set the bit 0 of register W3 to “1.”
Timer LC is the timer for LCD clock generating. Also, it can
be used as the multi-carrier generator by setting the bit 1 of
register W3 to “1” and selecting the system clock (STCK) as
a count source. When the multi-carrier generator is selected,
the waveform which is the timer LC underflow signal divided
by 2 can be output as a carrier wave from port CARR. At this
time, stop the carrier generating circuit and LCD control circuit.
When the multi-carrier generator (duty ratio: 1/2 fixed) is used,
the enable/stop of the carrier wave output from port CARR
can be set by the stop of timer LC or the carrier wave output
auto-control function by timer 1.
(7) Timer interrupt request flags (T1F and T2F)
Each timer interrupt request flag is set to “1” when each timer
underflows. The state of these flags can be examined with
the skip instructions (SNZT1 and SNZT2).
Use the interrupt control register V1 to select an interrupt or
a skip instruction.
An interrupt request flag is cleared to “0” when an interrupt
occurs or when the next instruction is skipped with a skip
instruction.
相關PDF資料 |
PDF描述 |
|---|---|
| M34554M8-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34554MC-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP64 |
| M34571G6FP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO24 |
| M34584EDFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M35047-XXXSP | 24 X 12 CHARACTERS CRT CHAR DSPL CTLR, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34551M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34551M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER |
| M34551M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34552G8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34552G8HFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。