- 您現在的位置：買賣IC網 > PDF目錄16862 > KSZ8851SNL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8851SNL PDF資料下載
參數資料
| 型號： | KSZ8851SNL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 58/80頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION KSZ8851SNL |
| 產品培訓模塊： | KSZ8851 10/100 Embedded Controllers |
| 標準包裝： | 1 |
| 系列： | LinkMD® |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8851SNL |
| 主要屬性： | 1 個端口，100BASE-TX/10BASE-T |
| 次要屬性： | SPI 接口，LinkMD 線纜診斷 |
| 已供物品： | 板，文檔 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 相關產品： | 576-3299-6-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-1-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-2-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3254-ND - IC CTLR MAC/PHY NON-PCI 32-QFN |
| 其它名稱： | 576-3293 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁當前第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Micrel, Inc.
KSZ8851SNL/SNLI
August 2009
61
M9999-083109-2.0
Bit
Default Value
R/W
Description
Bit 8: is corresponding to signal energy detected.
When the bit is set to 1, the PME pin 2 will be asserted when a corresponding wake-on-
LAN event is occurred.
When this bit is set to 0, the PME pin 2 will be not asserted when a corresponding wake-
on-LAN event is occurred.
7
0
RW
Auto Wake-Up Enable
This bit is used to enable automatically wake-up from low power state to normal power
state in energy detect mode if carrier (signal energy) is present more than wake-up time in
GSWUTR register. During the normal power state, the device can receive and transmit
packets.
When this bit is set to 1, the auto wake-up is enabled in energy detect mode.
When this bit is set to 0, the auto wake-up is disabled in energy detect mode.
6
0
RW
Wake-Up to Normal Operation Mode
This bit is used to control the device wake-up from low power state in energy detect mode
to normal operation mode if signal energy is detected longer than the programmed wake-
up time in GSWUTR register.
When this bit is set to 1, the device will automatically go to the normal operation mode
from energy detect mode.
When this bit is set to 0, the device will not automatically go to the normal mode from
energy detect mode.
This bit is only valid when Auto Wake-Up Enable (bit7) is set to 1.
5-2
0x0
RO
(W1C)
Wake-Up Event Indication
These four bits are used to indicate the KSZ8851SNL wake-up event status as below:
0000: No wake-up event.
0001: Wake-up from energy event detected. (Bit 2 also set to 1 in ISR register)
0010: Wake-up from link up event detected. (Bit 3 also set to 1 in ISR register)
0100: Wake-up from magic packet event detected.
1000: Wake-up from wakeup frame event detected.
If Wake-on-LAN to PME Output Enable bit[11:8] are set, the KSZ8851SNL also asserts
the PME pin 2. These bits are cleared on power up reset or by write 1. It is not modified
by either hardware or software reset. When these bits are cleared, the KSZ8851SNL de-
asserts the PME pin.
1-0
0x0
RW
Power Management Mode
These two bits are used to control the KSZ8851SNL power management mode as below:
00: Normal Operation Mode.
01: Energy Detect Mode. (two states in this mode either low power or normal power)
10: Soft Power Down Mode.
11: Power Saving Mode.
In energy detect mode under low power state, it can wake-up to normal operation mode
either from line or host wake-up (host CPU issues any one of registers read or write
access).
In soft power down mode, it can wake-up to normal operation mode only from host wake-
up (host CPU issues any one of registers read or write access).
Go-Sleep & Wake-Up Time Register (0xD6 – 0xD7): GSWUTR
This register contains the value which is used to control minimum Go-Sleep time period when the device from normal
power state to low power state or to control minimum Wake-Up time period when the device from low power state to
normal power state in energy detect mode.
Bit
Default
R/W
Description
15-8
0x08
RW
Wake-up Time
This value is used to control the minimum period that the energy has to be detected
consecutively before the device is waked-up from the low power state. The unit is 16ms
+/-80%, the default wake-up time is 128 ms (16ms x 8). Zero time (0x00) is not allowed
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADF4007EBZ1 | BOARD EVALUATION FOR ADF4007EB1 |
| V110C12C100B | CONVERTER MOD DC/DC 12V 100W |
| DWP-125-3/4-0-STK | HEATSHRINK POLY 3/4"X4' BLK |
| EBA30DRMD | CONN EDGECARD 60POS .125 SQ WW |
| H2MXH-2618M | DIP CABLE - HDM26H/AE26M/X |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8851SNL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851SNL |
| KSZ8851SNLI TR | 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with SPI Bus Interface (I-Temp, Lead free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851SNLITR | 制造商:Micrel 功能描述:Ethernet Controller Single Chip 100Mbps |
| KSZ8851SNLI-TR | 功能描述:Ethernet Controller 10/100 Base-T/TX PHY SPI Interface 32-MLF? (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 協議:以太網 功能:控制器 接口:SPI 標準:10/100 Base-T/TX PHY 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:32-VFQFN 裸露焊盤，32-MLF? 供應商器件封裝:32-MLF?（5x5） 標準包裝:1 |
| KSZ8851SNLTR | 制造商:Micrel Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。