- 您現在的位置：買賣IC網 > PDF目錄16862 > KSZ8851SNL-EVAL (Micrel Inc)BOARD EVALUATION KSZ8851SNL PDF資料下載
參數資料
| 型號： | KSZ8851SNL-EVAL |
| 廠商： | Micrel Inc |
| 文件頁數： | 19/80頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION KSZ8851SNL |
| 產品培訓模塊： | KSZ8851 10/100 Embedded Controllers |
| 標準包裝： | 1 |
| 系列： | LinkMD® |
| 主要目的： | 接口，以太網控制器（PHY 和 MAC） |
| 嵌入式： | 否 |
| 已用 IC / 零件： | KSZ8851SNL |
| 主要屬性： | 1 個端口，100BASE-TX/10BASE-T |
| 次要屬性： | SPI 接口，LinkMD 線纜診斷 |
| 已供物品： | 板，文檔 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 相關產品： | 576-3299-6-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-1-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3299-2-ND - IC CTLR MAC/PHY NON-PCI 32-MLF 576-3254-ND - IC CTLR MAC/PHY NON-PCI 32-QFN |
| 其它名稱： | 576-3293 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
Micrel, Inc.
KSZ8851SNL/SNLI
August 2009
26
M9999-083109-2.0
Register Name
[bit](offset)
Description
TXCR[3:0](0x70)
TXCR[8:5](0x70)
Set transmit control function as below:
Set bit 3 to enable transmitting flow control. Set bit 2 to enable transmitting padding.
Set bit 1 to enable transmitting CRC. Set bit 0 to enable transmitting block operation.
Set transmit checksum generation for ICMP, UDP, TCP and IP packet.
TXMIR[12:0](0x78)
The amount of free transmit memory available is represented in units of byte. The TXQ memory (6 KByte)
is used for both frame payload and control word.
TXQCR[0](0x80)
For single frame to transmit, set this bit 0 = 1(manual enqueue). the KSZ8851SNL will enable current TX
frame prepared in the TX buffer is queued for transmit, this is only transmit one frame at a time.
Note: This bit is self-clearing after the frame is finished transmitting. The software should wait for the bit to
be cleared before setting up another new TX frame.
TXQCR[1](0x80)
When this bit is written as 1, the KSZ8851SNL will generate interrupt (bit 6 in ISR register) to CPU when
TXQ memory is available based upon the total amount of TXQ space requested by CPU at TXNTFSR
(0x9E) register.
Note: This bit is self-clearing after the frame is finished transmitting. The software should wait for the bit to
be cleared before set to 1 again
TXQCR[2](0x80)
For multiple frames to transmit, set this bit 2 = 1 (auto-enqueue). the KSZ8851SNL will enable current all
TX frames prepared in the TX buffer are queued to transmit automatically.
RXQCR[3](0x82)
Set bit 3 to start DMA access from host CPU either read (receive frame data) or write (transmit data
frame)
TXFDPR[14](0x84)
Set bit 14 to enable TXQ transmit frame data pointer register increments automatically on accesses to the
data register.
IER[14][6](0x90)
Set bit 14 to enable transmit interrupt in Interrupt Enable Register
Set bit 6 to enable transmit space available interrupt in Interrupt Enable Register.
ISR[15:0](0x92)
Write 1 (0xFFFF) to clear all interrupt status bits after interrupt occurred in Interrupt Status Register.
TXNTFSR[15:0](0x9E)
The host CPU is used to program the total amount of TXQ buffer space which is required for next total
transmit frames size in double-word count.
Table 9. Registers Setting for Transmit Function Block
Driver Routine for Transmit Packet from Host Processor to KSZ8851SNL
The transmit routine is called by the upper layer to transmit a contiguous block of data through the Ethernet controller. It is
user’s choice to decide how the transmit routine is implemented. If the Ethernet controller encounters an error while
transmitting the frame, it’s the user’s choice to decide whether the driver should attempt to retransmit the same frame or
discard the data. The following Figures 11 and 12 shows the step-by-step for single and multiple transmit packets from
host processor to KSZ8851SNL.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADF4007EBZ1 | BOARD EVALUATION FOR ADF4007EB1 |
| V110C12C100B | CONVERTER MOD DC/DC 12V 100W |
| DWP-125-3/4-0-STK | HEATSHRINK POLY 3/4"X4' BLK |
| EBA30DRMD | CONN EDGECARD 60POS .125 SQ WW |
| H2MXH-2618M | DIP CABLE - HDM26H/AE26M/X |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8851SNL-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8851SNL |
| KSZ8851SNLI TR | 功能描述:以太網 IC 10/100BT Ethernet MAC + PHY with SPI Bus Interface (I-Temp, Lead free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8851SNLITR | 制造商:Micrel 功能描述:Ethernet Controller Single Chip 100Mbps |
| KSZ8851SNLI-TR | 功能描述:Ethernet Controller 10/100 Base-T/TX PHY SPI Interface 32-MLF? (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 協議:以太網 功能:控制器 接口:SPI 標準:10/100 Base-T/TX PHY 電壓 - 電源:1.8V，2.5V，3.3V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 封裝/外殼:32-VFQFN 裸露焊盤，32-MLF? 供應商器件封裝:32-MLF?（5x5） 標準包裝:1 |
| KSZ8851SNLTR | 制造商:Micrel Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。