- 您現在的位置：買賣IC網 > PDF目錄369586 > KC80524NY450128 Microprocessor PDF資料下載
參數資料
| 型號： | KC80524NY450128 |
| 英文描述： | Microprocessor |
| 中文描述： | 微處理器 |
| 文件頁數： | 19/81頁 |
| 文件大?。?/td> | 598K |
| 代理商： | KC80524NY450128 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
Mobile Intel
Celeron Processor (0.18μ) in BGA2 and Micro-PGA2 Packages
Order Number#249563-001
Datasheet
19
Table 7. Recommended Resistors for Mobile Intel Celeron Processor Signals
Recommended
Resistor Value (
W
)
Mobile Intel Celeron Processor Signal
1, 2
10 pull-down
BREQ0#
3
RESET#
4
56.2 pull-up
150 pull-up
PICD[1:0], TDI, TDO
270 pull-up
SMI#
680 pull-up
STPCLK#
1K pull-up
INIT#, TCK, TMS
1K pull-down
TRST#
1.5K pull-up
A20M#, FERR#, FLUSH#, IERR#, IGNNE#, LINT0/INTR,
LINT1/NMI, PREQ#, PWRGOOD, SLP#
NOTES:
1.
The recommendations above are only for signals that are being used. These recommendations are
maximum values only; stronger pull-ups may be used. Pull-ups for the signals driven by the chipset should
not violate the chipset specification. Refer to Section 3.1.4 for the required pull-up or pull-down resistors for
signals that are not being used.
Open-drain signals must never violate the undershoot specification in Section 4.3. Use stronger pull-ups if
there is too much undershoot.
A pull-down on BREQ0# is an alternative to having the central agent to drive BREQ0# low at reset.
A 56.2
1% terminating resistor connected to V
CCT
is required.
2.
3.
4.
3.1.1
Power Sequencing Requirements
The mobile Intel Celeron processor has no power sequencing requirements. Intel recommends that
all of the processor power planes rise to their specified values within one second of each other.
The V
CC
power plane must not rise too fast. At least 200
μ
sec (T
R
) must pass from the time that
V
CC
is at 10% of its nominal value until the time that V
CC
is at 90% of its nominal value (see
Figure 3).
Figure 3. Vcc Ramp Rate Requirement
Vcc
Volts
90% Vcc (nominal)
10% Vcc (nominal)
T
R
Time
3.1.2
Test Access Port (TAP) Connection
The TAP interface is an implementation of the IEEE 1149.1 (“JTAG”) standard. Due to the
voltage levels supported by the TAP interface, Intel recommends that the mobile Intel Celeron
processor and the other 1.5-V JTAG specification compliant devices be last in the JTAG chain
after any devices with 3.3-V or 5.0-V JTAG interfaces within the system. A translation buffer
相關PDF資料 |
PDF描述 |
|---|---|
| KP80524NY450128 | Microprocessor |
| RH8053GC017512 | Microprocessor |
| RH8053GC021512 | Microprocessor |
| RH8053GC025512 | Microprocessor |
| RH8053GC029512 | Microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KC80526GY001256S L54F | 制造商:Intel 功能描述:MPU Pentium |
| KC80526GY650256 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| KC80526GY6504JY | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Intel 功能描述: |
| KC80526GY850256S L547 | 制造商:Intel 功能描述:MPU Pentium 制造商:Intel 功能描述:MPU Pentium? III Processor 64-Bit 0.18um 850MHz 495-Pin BGA2 |
| KC80526GY850256SL547 | 功能描述:IC PENTIUM 3 1.6V 850MHZ 495-BGA RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微處理器 系列:- 標準包裝:2 系列:MPC8xx 處理器類型:32-位 MPC8xx PowerQUICC 特點:- 速度:133MHz 電壓:3.3V 安裝類型:表面貼裝 封裝/外殼:357-BBGA 供應商設備封裝:357-PBGA（25x25） 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。