- 您現在的位置：買賣IC網 > PDF目錄383036 > GS8180D18 (GSI TECHNOLOGY) 1Mb x 18Bit Separate I/O Sigma DDR SRAM(1M x 18位獨立I/O接口雙數據速率讀和寫模式靜態ΣRAM) PDF資料下載
參數資料
| 型號： | GS8180D18 |
| 廠商： | GSI TECHNOLOGY |
| 英文描述： | 1Mb x 18Bit Separate I/O Sigma DDR SRAM(1M x 18位獨立I/O接口雙數據速率讀和寫模式靜態ΣRAM) |
| 中文描述： | 1兆x 18位獨立的I / O西格瑪?shù)腄DR SRAM的（100萬× 18位獨立的I / O接口雙數據速率讀和寫模式靜態ΣRAM） |
| 文件頁數： | 25/33頁 |
| 文件大小： | 874K |
| 代理商： | GS8180D18 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
Rev: 1.01 11/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
25/33
2000, Giga Semiconductor, Inc.
A
Advanced Information
GS8180D09/18B-333/300/275/250
JTAG TAP Block Diagram
Identification (ID) Register
The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in
Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM.
It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the
controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins.
ID Register Contents
Tap Controller Instruction Set
Overview
There are two classes of instructions defined in the Standard 1149.1-1990—the standard (Public) instructions, and device specific
(Private) instructions. Some Public instructions are mandatory for 1149.1 compliance. Optional Public instructions must be
implemented in prescribed ways. Although the TAP controller in this device follows the 1149.1 conventions, it is not 1194.1-
compliant because some of the mandatory instructions are uniquely implemented. The TAP on this device may be used to monitor
all input and I/O pads, but cannot be used to load address, data or control signals into the RAM or to preload the I/O buffers.This
device will not perform INTEST or the preload portion of the SAMPLE/PRELOAD command.
Die
Revision
Code
Not Used
I/O
Configuration
GSI Technology
JEDEC Vendor
ID Code
P
Bit #
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
X
X
X
X
0
0
0
0
0
0
0
0
0
0
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
1
1
x09
0
0
0
0
1
1
1
0
1
1
0
0
0
0
0
0
0 1 1 0 1 1 0 0 1
0 1 1 0 1 1 0 0 1
x18
Instruction Register
ID Code Register
·
31 30 29
Boundary Scan Register
· · ·
· · ·
n
0
1
2
0
1
2
· · ·
0
1
2
· · ·
0
Bypass Register
TDI
TDO
TMS
TCK
Test Access Port (TAP) Controller
相關PDF資料 |
PDF描述 |
|---|---|
| GS8180S36 | 512K x 36Bit Separate I/O Sigma DDR SRAM(512K x 36位獨立I/O接口雙數據速率讀和寫模式靜態ΣRAM) |
| GS8180S18 | 1Mb x 18Bit Separate I/O Sigma DDR SRAM(1M x 18位獨立I/O接口雙數據速率讀和寫模式靜態ΣRAM) |
| GS8180S09 | 2Mb x 9Bit Separate I/O Sigma DDR SRAM(2M x 9位獨立I/O接口雙數據速率讀和寫模式靜態ΣRAM) |
| GS820322T-138 | 64K x 32 2M Synchronous Burst SRAM |
| GS82032Q-100 | 64K x 32 2M Synchronous Burst SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS8180Q36D-167X | 制造商:GSI Technology 功能描述:512K X 36 (18 MEG)SIGMA QUAD I -SEPERATE I/O BURST OF 2 - Trays |
| GS8180QV36BGD-167 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V 18MBIT 512KX36 2.5NS 165FPBGA - Trays |
| GS8180QV36BGD-167I | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V 18MBIT 512KX36 2.5NS 165FPBGA - Trays |
| GS8182D08BD-167 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V 16MBIT 2MX8 0.5NS 165FPBGA - Trays |
| GS8182D08BD-250 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V 16MBIT 2MX8 0.45NS 165FPBGA - Trays |
發布緊急采購，3分鐘左右您將得到回復。