參數資料
型號： ADUC7039BCP6Z-RL
廠商： Analog Devices Inc
文件頁數： 72/92頁
文件大?。?/td> 0K
描述： IC MCU ARM7 BATT SENSER 32LFCSP
標準包裝： 2,500
系列： MicroConverter® ADuC7xxx
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 20.48MHz
連通性： LIN，SPI
外圍設備： POR，溫度傳感器，WDT
輸入/輸出數： 6
程序存儲器容量： 64KB（32K x 16）
程序存儲器類型： 閃存
RAM 容量： 1K x 32
電壓 - 電源 (Vcc/Vdd)： 3.5 V ~ 18 V
數據轉換器： A/D 2x16b
振蕩器型： 內部
工作溫度： -40°C ~ 115°C
封裝/外殼： 32-VFQFN 裸露焊盤，CSP
包裝： 帶卷 (TR)
ADuC7039
Data Sheet
Rev. D | Page 74 of 92
SERIAL PERIPHERAL INTERFACE (SPI)
The ADuC7039 integrates a complete hardware serial peri-
pheral interface (SPI) on-chip. SPI is an industry standard,
synchronous serial interface that allows eight bits of data to
be synchronously transmitted and simultaneously received,
that is, full duplex up to a maximum bit rate of 5.12 Mb.
The SPI port can be configured for master or slave operation
and typically consists of four pins: MISO, MOSI, SCLK, and SS.
MASTER IN, SLAVE OUT (MISO) PIN
The MISO pin is configured as an input line in master mode
and an output line in slave mode. The MISO line on the master
(data in) should be connected to the MISO line in the slave
device (data out). The data is transferred as byte wide (8-bit)
serial data, MSB first.
MASTER OUT, SLAVE IN (MOSI) PIN
The MOSI pin is configured as an output line in master mode
and an input line in slave mode. The MOSI line on the master
(data out) should be connected to the MOSI line in the slave
device (data in). The data is transferred as byte wide (8-bit)
serial data, MSB first.
SERIAL CLOCK I/O (SCLK) PIN
The master serial clock (SCLK) synchronizes the data being
transmitted and received through the MOSI SCLK period.
Therefore, a byte is transmitted/received after eight SCLK
periods. The SCLK pin is configured as an output in master
mode and as an input in slave mode.
In master mode, polarity and phase of the clock are controlled
by the SPICON register, and the bit rate is defined in the SPIDIV
register as follows:
)
1
(
2
MHz
48
.
20
SPIDIV
f
K
SERIALCLOC
+
×
=
The maximum bit rate in master mode is 10.24 Mb. In slave
mode, the SPICON register must be configured with the phase
and polarity of the expected input clock. The slave accepts data
from an external master up to 5.12 Mb.
In both master and slave modes, data is transmitted on one
edge of the SCLK signal and sampled on the other. Therefore,
it is important that the polarity and phase are configured the
same for the master and slave devices.
SLAVE SELECT (SS) PIN
In SPI slave mode, a transfer is initiated by the assertion of SS,
which is an active low input signal. The SPI port then transmits
and receives 8-bit data until the transfer is concluded by deas-
sertion of SS. In slave mode, SS is always an input.
In SPI master mode, the SS is an active low output signal. It
asserts itself automatically at the beginning of a transfer and
deasserts itself upon completion.
SPI MMR INTERFACE
The following MMR registers control the SPI interface: SPISTA,
SPIRX, SPITX, SPIDIV, and SPICON.
SPIRX Register
Name:
SPIRX
Address:
0xFFFF0A04
Default Value:
0x00
Access:
Read only
Function:
This 8-bit MMR is the SPI receive register.
SPITX Register
Name:
SPITX
Address:
0xFFFF0A08
Default Value:
N/A
Access:
Write only
Function:
This 8-bit MMR is the SPI transmit register.
SPIDIV Register
Name:
SPIDIV
Address:
0xFFFF0A0C
Default Value: 0x00
Access:
Read/Write
Function:
This 6-bit MMR is the SPI baud rate selection
register.
相關PDF資料
PDF描述
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
ADUC7121BBCZ-RL PRECISION ANALOG MCU I.C
ADUC7122BBCZ-RL PRECISION ANALOG MCU I.C
ADUC7126BSTZ126-RL IC MCU 16/32B 126KB FLASH 80LQFP
ADUC7129BSTZ126 IC DAS MCU ARM7 ADC/DDS 80-LQFP
相關代理商/技術參數
參數描述
ADUC7039WBCPZ 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Trays 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
ADUC7039WBCPZ-RL 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C.
ADUC7060 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Precision Analog Microcontroller, Dual Sigma-Delta ADCs, Flash/EE, ARM7TDMI
ADUC7060BCPZ32 功能描述:IC MCU 24BIT 32KB FLASH 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
ADUC7060BCPZ32-RL 功能描述:IC MCU FLASH 24BIT 32KB 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*