- 您現在的位置：買賣IC網 > PDF目錄1900 > ADUC7039BCP6Z-RL (Analog Devices Inc)IC MCU ARM7 BATT SENSER 32LFCSP PDF資料下載
參數資料
| 型號： | ADUC7039BCP6Z-RL |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 35/92頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU ARM7 BATT SENSER 32LFCSP |
| 標準包裝： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 20.48MHz |
| 連通性： | LIN，SPI |
| 外圍設備： | POR，溫度傳感器，WDT |
| 輸入/輸出數： | 6 |
| 程序存儲器容量： | 64KB（32K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 32 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.5 V ~ 18 V |
| 數據轉換器： | A/D 2x16b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 115°C |
| 封裝/外殼： | 32-VFQFN 裸露焊盤，CSP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁
ADuC7039
Data Sheet
Rev. D | Page 40 of 92
ADC Configuration Register
Name:
ADCCFG
Address:
0xFFFF051C
Default Value:
0x00
Access:
Read/write
Function:
The 8-bit ADC configuration MMR controls extended functionality related to the on-chip ADCs.
Table 34. ADCCFG MMR Bit Designations
Bit
Description
7
Analog ground switch enable.
This bit is set to 1 by user software to connect the external GND_SW pin (Pin 9) to an internal 20 kΩ resistor to ground.
This bit can be used to connect and disconnect external circuits and components to ground under program control and
thereby minimize dc current consumption when the external circuit or component is not being used.
6 to 5
Not used. These bits are reserved for future functionality and should not be modified by user code.
4
Current channel ADC accumulator enable.
0 = accumulator disabled and reset to 0. The accumulator must be disabled for a full ADC conversion (ADCSTA[0] set
twice) before the accumulator can be re-enabled to ensure the accumulator is reset.
1 = accumulator enabled.
3
Current channel ADC comparator enable.
0 = comparator disabled.
1 = comparator active, interrupt asserted if absolute value of I-ADC conversion result |I| ≥ ADC0TH.
2
Not used. This bit is reserved for future functionality and should be written as 0 by user code.
1
Fast temperature sensor mode.
This bit is set by the user to enable the feature described in the Fast Temperature Conversion Mode section. When this
bit is set, ADC1CON[7:6] is temporarily ignored to produce a single fully settled result of the internal temperature
sensor. This fast conversion mode is applicable to the internal temperature sensor only.
This bit should be cleared by the user when the fast conversion is complete.
0
Current channel ADC, result counter enable.
This bit is set by the user to enable the result count mode. In this mode, an I-ADC interrupt is generated only when
ADC0RCV = ADC0RCL. This allows the I-ADC to continuously monitor current but only interrupt the MCU core after a
defined number of conversions. The voltage/temperature ADC also continues to convert if enabled, but again, only
the last conversion result is available (intermediate V/T-ADC conversion results are not stored) when the ADC counter
interrupt occurs.
Current Channel ADC Data Register
Name:
ADC0DAT
Address:
0xFFFF0520
Default Value:
0x0000
Access:
Read only
Function:
This ADC data MMR holds the 16-bit conver-
sion result from the I-ADC. The ADC does
not update this MMR if the ADC0 conversion
result ready bit (ADCSTA[0]) is set. A read of
this MMR by the MCU clears all asserted
ready flags (ADCSTA[2:0] and ADCSTA[5]).
Voltage/Temperature Channel ADC Data Register
Name:
ADC1DAT
Address:
0xFFFF0524
Default Value: 0x0000
Access:
Read only
Function:
This ADC data MMR holds the 16-bit voltage
(or temperature) conversion result from the
V/T-ADC. The ADC does not update this
MMR if the voltage (or temperature) conversion
result ready bit (ADCSTA[1] or ADCSTA[2])
is set. If I-ADC is not active, a read of this
MMR by the MCU clears all asserted ready
flags (ADCSTA[2:1] and ADCSTA[5]).
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC7061BCPZ32 | IC MCU 16/32BIT 32KB 32LFCSP |
| ADUC7121BBCZ-RL | PRECISION ANALOG MCU I.C |
| ADUC7122BBCZ-RL | PRECISION ANALOG MCU I.C |
| ADUC7126BSTZ126-RL | IC MCU 16/32B 126KB FLASH 80LQFP |
| ADUC7129BSTZ126 | IC DAS MCU ARM7 ADC/DDS 80-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC7039WBCPZ | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Trays 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7039WBCPZ-RL | 制造商:Analog Devices 功能描述:FLASH 64K ARM7 DUAL 16-BIT ADC LIN I.C. - Tape and Reel 制造商:Analog Devices 功能描述:IC MCU ARM7 64KB FLASH 32LFCSP 制造商:Analog Devices 功能描述:Flash 64k ARM7 Dual 16-Bit ADC LIN I.C. |
| ADUC7060 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Power, Precision Analog Microcontroller, Dual Sigma-Delta ADCs, Flash/EE, ARM7TDMI |
| ADUC7060BCPZ32 | 功能描述:IC MCU 24BIT 32KB FLASH 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM |
| ADUC7060BCPZ32-RL | 功能描述:IC MCU FLASH 24BIT 32KB 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND |
發(fā)布緊急采購，3分鐘左右您將得到回復。