參數資料
型號: ADUC7034BCPZ
廠商: Analog Devices Inc
文件頁數: 20/136頁
文件大?。?/td> 0K
描述: IC MCU FLASH 32K ANLG IO 48LFCSP
標準包裝: 1
系列: MicroConverter® ADuC7xxx
核心處理器: ARM7
芯體尺寸: 16/32-位
速度: 20.48MHz
連通性: LIN,SPI,UART/USART
外圍設備: POR,PSM,溫度傳感器,WDT
輸入/輸出數: 9
程序存儲器容量: 32KB(16K x 16)
程序存儲器類型: 閃存
RAM 容量: 1K x 32
電壓 - 電源 (Vcc/Vdd): 3.5 V ~ 18 V
數據轉換器: A/D 2x16b
振蕩器型: 內部
工作溫度: -40°C ~ 115°C
封裝/外殼: 48-VFQFN 裸露焊盤,CSP
包裝: 托盤
ADuC7034
Rev. B | Page 116 of 136
SERIAL TEST INTERFACE OUTPUT STRUCTURE
The serial test interface is a high voltage output that incorporates
a low-side driver, short-circuit protection, and diagnostic pin
readback capability. The output driver circuit configuration is
shown in Figure 44.
PIN
READBACK
HVMON[5]
STI
TRANSMIT
GP2CON[24]
REF1
SHORT-CIRCUIT
PROTECTION CONTROL
HVCFG1[2]
STI
07
11
6-
0
40
Figure 44. STI Output Structure
USING THE SERIAL TEST INTERFACE
Data only begins transmission when the STI port is configured
as follows:
1.
Configure Timer4 for baud rate generation.
2.
Correctly enable STICON using STIKEY0 and STIKEY1
for secure access.
3.
Write the required bytes to be transmitted into STIDAT0,
STIDAT1, and STIDAT2.
Timer4 is configured with the correct load value to generate an
overflow at the required baud rate. If the STI port is used to
transmit ADC conversion results, the baud rate must be
sufficient to output each ADC result (16 bits) before the next
ADC conversion result is available.
For example, if the ADC is sampling at 1 kHz, the baud rate
must be sufficient to output 36 bits as follows: (3 × 8 bits (16-bit
ADC result and a checksum byte, for example)) + (3 × 1 start
bit) + (3 × 1 parity bit) + (3 × 2 stop bits) = 36 bits.
Therefore, the serial test interface must transmit data at greater
than 36 kbps. The closest standard baud rate is 38.4 kbps; as
such, the reload value written to the Timer4 load MMR (T4LD)
is 0x0106 (267 decimal). This value is based on a prescaler of 1
and is calculated as follows using a core clock of 10.24 MHz:
267
kbps
4
.
38
MHz
24
.
10
=
Rate
Baud
Desired
Frequency
Clock
Core
T4LD
When the Timer4 load value is written and the timer itself is
configured and enabled using the T4CON MMR, the STI port
must be configured. This is accomplished by writing to the
STICON MMR in a specific sequence using the STIKEY0 and
STIKEY1 MMRs as described in the previous sections.
Finally, the STI port does not begin transmission until the required
number of transmit bytes are written into the STIDATx MMRs. As
soon as STI starts transmitting, the value in the STICON MMR
changes from the value initially written to this register. User code
can ensure that all data is transmitted by continuously polling
the STICON MMR until it reverts back to the value originally
written to it. To disable the serial interface, user code must write
a 0 to STICON[0].
An example code segment configuring the STI port to transmit five bytes and then to transmit two bytes follows:
T4LD = 267;
// Timer4 reload value
T4CON = 0xC0;
// Enable T4, selecting core clock in periodic mode
STIKEY0 = 07;
// STICON start write sequence
STICON = 0x11;
// Enable and transmit five bytes
STIKEY1 = 0xb9;
// STICON complete write
STIDAT0 = 0xAABB;
// Five bytes for
STIDAT1 = 0xCCDD;
// transmission
STIDAT2 = 0xFF;
while(STICON != 0x09)
// Wait for transmission to complete
{}
STIKEY0 = 07;
// STICON start write sequence
STICON = 0x05;
// Enable and transmit two bytes
STIKEY1 = 0xb9;
// STICON complete write
STIDAT0 = 0xEEFF;
// Two bytes for transmission
while(STICON != 0x09)
// Wait for transmission to complete
{}
相關PDF資料
PDF描述
ADUC7036CCPZ IC MCU 96K FLASH DUAL 48LFCSP
ADUC7039BCP6Z-RL IC MCU ARM7 BATT SENSER 32LFCSP
ADUC7061BCPZ32 IC MCU 16/32BIT 32KB 32LFCSP
ADUC7121BBCZ-RL PRECISION ANALOG MCU I.C
ADUC7122BBCZ-RL PRECISION ANALOG MCU I.C
相關代理商/技術參數
參數描述
ADUC7034BCPZ-RL 功能描述:IC MCU FLASH 32K ANLG IO 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA,UART/USART 外圍設備:欠壓檢測/復位,LED,POR,PWM,WDT 輸入/輸出數:16 程序存儲器容量:4KB(4K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7036 制造商:AD 制造商全稱:Analog Devices 功能描述:Integrated Precision Battery Sensor for Automotive
ADUC7036BCPZ 功能描述:IC MCU FLASH 96K ANLGI/O 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA,UART/USART 外圍設備:欠壓檢測/復位,LED,POR,PWM,WDT 輸入/輸出數:16 程序存儲器容量:4KB(4K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7036BCPZ-RL 功能描述:IC SENSOR AUTO 96K FLASH 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA,UART/USART 外圍設備:欠壓檢測/復位,LED,POR,PWM,WDT 輸入/輸出數:16 程序存儲器容量:4KB(4K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC7036CCPZ 功能描述:IC MCU 96K FLASH DUAL 48LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC7xxx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA,UART/USART 外圍設備:欠壓檢測/復位,LED,POR,PWM,WDT 輸入/輸出數:16 程序存儲器容量:4KB(4K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND