- 您現在的位置：買賣IC網 > PDF目錄373973 > AD9995 (Analog Devices, Inc.) 12-Bit CCD Signal Processor with Precision Timing ⑩ Generator PDF資料下載
參數資料
| 型號： | AD9995 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 12-Bit CCD Signal Processor with Precision Timing ⑩ Generator |
| 中文描述： | 12位CCD信號處理器與精密計時⑩發生器 |
| 文件頁數： | 39/60頁 |
| 文件大?。?/td> | 1593K |
| 代理商： | AD9995 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
AD9995
–39–
Updating New Register Values
The AD9995’s internal registers are updated at different times,
depending on the particular register. Table XV summarizes the
four different types of register updates:
1.
SCK Updated
: Some of the registers in Bank 1 are updated
immediately, as soon as the 24th data bit (D23) is written.
These registers are used for functions that do not require gat-
ing with the next VD boundary, such as power-up and reset
functions. These registers are lightly shaded in gray in the
Bank 1 register list.
The Bank Select register (Addr. 0x7F in Bank 1 and 2) is also
SCK updated.
2.
VD Updated
: Most of the registers in Bank 1, as well as the
Field registers in Bank 2, are updated at the next VD falling
edge. By updating these values at the next VD edge, the cur-
rent field will not be corrupted and the new register values
will be applied to the next field. The Bank 1 register updates
may be further delayed past the VD falling edge by using
the UPDATE register (Addr. 0x19). This will delay the VD
updated register updates to any HD line in the field. Note that
the Bank 2 registers are not affected by the UPDATE register.
3.
SG-Line Updated
: A few of the registers in Bank 1 are
updated at the end of the SG active line, at the HD falling
edge. These are the registers to control the SUBCK signal so
that the SUBCK output will not be updated until after the SG
line has been completed. These registers are darkly shaded in
gray in the Bank 1 register list.
4.
SCP Updated
: In Bank 2, all of the V-pattern group and
V-sequence registers (Addr. 0x00 through 0xCF, exclud-
ing 0x7F) are updated at the next SCP, where they will
be used. For example, in Figure 42, this field has selected
Region 1 to use V-Sequence 3 for the vertical outputs. This
means that a write to any of the V-Sequence 3 registers, or
any of the V-pattern group registers that are referenced by
V-Sequence 3 will be updated at SCP1. If multiple writes
are done to the same register, the last one done before SCP1
will be the one that is updated. Likewise, register writes to
any V-Sequence 5 registers will be updated at SCP2, and
register writes to any V-Sequence 8 registers will be updated
at SCP3.
Table XV. Register Update Locations
Description
Register is immediately updated when the 24th data bit (D23) is clocked in.
Register is updated at the VD falling edge. VD updated registers in Bank 1 may be
delayed further by using the UPDATE register at Address 0x19 in Bank 1. Bank 2
updates will not be affected by the UPDATE register.
Register is updated at the HD falling edge at the end of the SG-active line.
Register is updated at the next SCP when the register will be used.
Update Type
SCK Updated
VD Updated
Register Bank
Bank 1 Only
Bank 1 and Bank 2
SG Line Updated
SCP Updated
Bank 1 Only
Bank 2 Only
VD
REGION 0
HD
SCP 1
SCP 2
SCP 3
REGION 1
REGION 2
REGION 3
VSG
SGLINE
SCP 0
SERIAL
WRITE
SCK
UPDATED
SCP 0
VD
UPDATED
SG
UPDATED
SCP
UPDATED
V1–V6
USE VSEQ2
USE VSEQ3
USE VSEQ5
USE VSEQ8
Figure 42. Register Update Locations (See Table XV for Definitions)
REV. 0
相關PDF資料 |
PDF描述 |
|---|---|
| ADA4000-2ARMZ-RL | Low Cost, Precision JFET Input Operational Amplifiers |
| ADA4000-1 | Low Cost, Precision JFET Input Operational Amplifiers |
| ADA4000-1_07 | Low Cost, Precision JFET Input Operational Amplifiers |
| ADA4000-1ARZ | Low Cost, Precision JFET Input Operational Amplifiers |
| ADA4000-1ARZ-R7 | Low Cost, Precision JFET Input Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9995KCP | 制造商:Analog Devices 功能描述:AFE Video 1ADC 12-Bit 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:12 BIT 36 MSPS ANALOG FRONT END CONVERTE - Bulk |
| AD9995KCPRL | 制造商:Analog Devices 功能描述:AFE Video 1ADC 12-Bit 3V 56-Pin LFCSP EP T/R 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD9995KCPZ | 功能描述:IC CCD SIGNAL PROCESSOR 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9995KCPZRL | 功能描述:IC CCD SIGNAL PROCESSOR 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9995KCPZRL7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。