- 您現在的位置：買賣IC網 > PDF目錄373962 > AD9260AS (ANALOG DEVICES INC) High-Speed Oversampling CMOS ADC with 16-Bit Resolution at a 2.5 MHz Output Word Rate PDF資料下載
參數資料
| 型號： | AD9260AS |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | High-Speed Oversampling CMOS ADC with 16-Bit Resolution at a 2.5 MHz Output Word Rate |
| 中文描述： | 1-CH 16-BIT PROPRIETARY METHOD ADC, PARALLEL ACCESS, PQFP44 |
| 封裝： | MS-022AB, MQFP-44 |
| 文件頁數： | 10/36頁 |
| 文件大小： | 572K |
| 代理商： | AD9260AS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
AD9260
–10–
REV. B
DEFINITIONS OF SPECIFICATION
INTEGRAL NONLINEARITY (INL)
INL refers to the deviation of each individual code from a line
drawn from
“
negative full scale
”
through
“
positive full scale.
”
The point used as
“
negative full scale
”
occurs 1/2 LSB before
the first code transition.
“
Positive full scale
”
is defined as a
level 1 1/2 LSB beyond the last code transition. The deviation
is measured from the middle of each particular code to the true
straight line.
DIFFERENTIAL NONLINEARITY (DNL, NO MISSING
CODES)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 14-bit resolution indicates that all 16384
codes, respectively, must be present over all operating ranges.
NOTE: Conventional INL and DNL measurements don
’
t really
apply to
Σ
converters: the DNL looks continually better if
longer data records are taken. For the AD9260, INL and DNL
numbers are given as representative.
ZERO ERROR
The major carry transition should occur for an analog value
1/2 LSB below VINA = VINB. Zero error is defined as the
deviation of the actual transition from that point.
GAIN ERROR
The first code transition should occur at an analog value
1/2 LSB above negative full scale. The last transition should
occur at an analog value 1 1/2 LSB below the nominal full scale.
Gain error is the deviation of the actual difference between first
and last code transitions and the ideal difference between first
and last code transitions.
TEMPERATURE DRIFT
The temperature drift for zero error and gain error specifies the
maximum change from the initial (+25
°
C) value to the value at
T
MIN
or T
MAX
.
POWER SUPPLY REJECTION
The specification shows the maximum change in full scale from
the value with the supply at the minimum limit to the value with
the supply at its maximum limit.
APERTURE JITTER
Aperture jitter is the variation in aperture delay for successive
samples and is manifested as noise on the input to the A/D.
SIGNAL-TO-NOISE AND DISTORTION (S/N+D, SINAD)
RATIO
S/N+D is the ratio of the rms value of the measured input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc.
The value for S/N+D is expressed in decibels.
EFFECTIVE NUMBER OF BITS (ENOB)
For a sine wave, SINAD can be expressed in terms of the num-
ber of bits. Using the following formula,
N
= (
SINAD
–
1.76)/6.02
it is possible to get a measure of performance expressed as
N
,
the effective number of bits.
Thus, effective number of bits for a device for sine wave inputs
at a given input frequency can be calculated directly from its
measured SINAD.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first six harmonic com-
ponents to the rms value of the measured input signal and
is expressed as a percentage or in decibels.
SIGNAL-TO-NOISE RATIO (SNR)
SNR is the ratio of the rms value of the measured input signal to
the rms sum of all other spectral components below the Nyquist
frequency, excluding the first six harmonics and dc. The value
for SNR is expressed in decibels.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
SFDR is the difference in dB between the rms amplitude of the
input signal and the peak spurious signal.
TWO-TONE SFDR
The ratio of the rms value of either input tone to the rms value
of the peak spurious component. The peak spurious component
may or may not be an IMD product. May be reported in dBc
(i.e., degrades as signal level is lowered), or in dBFS (always
related back to converter full scale).
相關PDF資料 |
PDF描述 |
|---|---|
| AD9260EB | High-Speed Oversampling CMOS ADC with 16-Bit Resolution at a 2.5 MHz Output Word Rate |
| AD9280ARSRL | Complete 8-Bit, 32 MSPS, 95 mW CMOS A/D Converter |
| AD9280 | Complete 8-Bit, 32 MSPS, 95 mW CMOS A/D Converter |
| AD9280-EB | Complete 8-Bit, 32 MSPS, 95 mW CMOS A/D Converter |
| AD9280ARS | Complete 8-Bit, 32 MSPS, 95 mW CMOS A/D Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9260ASRL | 制造商:Analog Devices 功能描述:ADC Single Pipelined 2.5Msps 16-bit Parallel 44-Pin MQFP T/R 制造商:Rochester Electronics LLC 功能描述:16-BIT HIGH SPEED OVERSAMPLED ADC - Bulk |
| AD9260ASZ | 功能描述:IC ADC CMOS 16BIT OVRSAMP 44MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| AD9260ASZRL | 功能描述:IC ADC 16BIT 2.5MHZ 44MQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9260EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:High-Speed Oversampling CMOS ADC with 16-Bit Resolution at a 2.5 MHz Output Word Rate |
| AD9260-EB | 制造商:Analog Devices 功能描述:Evaluation Board For AD9260 制造商:Analog Devices 功能描述:DEV TOOLS, EVAL BD FOR AD9260 - Bulk |
發布緊急采購，3分鐘左右您將得到回復。