- 您現在的位置：買賣IC網 > PDF目錄2018 > XRD98L59AIGTR (Exar Corporation)IC CCD DIGITIZER 10BIT 28TSSOP PDF資料下載
參數資料
| 型號： | XRD98L59AIGTR |
| 廠商： | Exar Corporation |
| 文件頁數： | 36/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CCD DIGITIZER 10BIT 28TSSOP |
| 產品變化通告： | Obsolescence Notification 15/Apr/2010 |
| 標準包裝： | 1,500 |
| 位數： | 10 |
| 通道數： | 1 |
| 電壓 - 電源，模擬： | 2.7 V ~ 3.6 V |
| 電壓 - 電源，數字： | 2.7 V ~ 3.6 V |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 28-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁
XRD98L59
8
Rev. 2.00
SERIAL INTERFACE
The XRD98L59 uses a three wire serial interface (LOAD,
SDI & SCLK) to access the programmable features and
controls of the chip.The serial interface uses a 12-bit shift
register. The first 4 bits shifted in are the address bits, the
next 8 bits are the data bits. The address bits select
which of the internal registers will receive the 8 data bits.
There is no checking or read back of the address bits to
ensure a valid register is written to. If the address bits
select an undefined register, the data will be discarded.
SCLK
SDI
LOAD
Time
A 3
A 2
A 1
A 0
D7
D6
D5
D4
D3
D2
D1
D0
t1
t2
t12
t11
…
t
L1
t
L2
t
SCLK
t
set
t
hold
MSB
L S B
SERIAL PORT PROCEDURES
1)
Set LOAD pin low to enable shift register.
2)
Shift in 4 address bits (msb first), followed by
8 data bits (msb first).
3)
Set LOAD pin high to transfer data from the
shift register to the serial interface register
array.
For optimum image quality, do not run the serial port
during active video. Serial port clocking can couple into
the signal path and degrade accuracy. Also, do not
continuously run SCLK.
Reseting the XRD98L59 is recommended after initial
power-up. It is generally good practice to reset the
XRD98L59 because the serial data may be forced to an
unknown state during power supply cycling by the digital
ASIC.
Figure 3. Serial Interface Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| XRD98L61AIV-F | IC CCD DIGITIZER 12BIT 48TQFP |
| XRD98L62ACV-F | IC CCD DIGITIZER 12BIT 48TQFP |
| XRD98L63AIV-F | IC CCD DIGITIZER 12BIT 48TQFP |
| XRT71D00IQ-F | IC JITTER ATTENUATOR SGL 32TQFP |
| XRT71D03IV-F | IC JITTER ATTENUATOR 3CH 64TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRD98L59AIGTR-F | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| XRD98L61 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D |
| XRD98L61_01 | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D |
| XRD98L61AIV | 制造商:EXAR 制造商全稱:EXAR 功能描述:CCD Image Digitizers with CDS, PGA and 12-Bit A/D |
| XRD98L61AIV-F | 功能描述:視頻 IC RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。