- 您現在的位置：買賣IC網 > PDF目錄383985 > USB3450-FZG (STANDARD MICROSYSTEMS CORP) HI-SPEED USB HOST OR DEVICE PHY WITH UTMI+INTERFACE PDF資料下載
參數資料
| 型號： | USB3450-FZG |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HI-SPEED USB HOST OR DEVICE PHY WITH UTMI+INTERFACE |
| 中文描述： | SERIAL COMM CONTROLLER, QCC40 |
| 封裝： | 6 X 6 MM, 0.90 MM HEIGHT, 0.50 MM PITCH, ROHS COMPLIANT, MO-220, QFN-40 |
| 文件頁數： | 36/40頁 |
| 文件大?。?/td> | 1086K |
| 代理商： | USB3450-FZG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁
Hi-Speed USB Host or Device PHY With UTMI+ Interface
Datasheet
Revision 0.1 (05-11-05)
36
SMSC USB3450
DATASHEET
To detect the assertion of the downstream Chirp K's and Chirp J's for 2.5us {T
FILT
}, the Link must see
the appropriate LINESTATE signals asserted continuously for 165 CLKOUT cycles.
7.11
Assertion of Resume
In this case, an event internal to the device initiates the resume process. A device with remote wake-
up capability must wait for at least 5ms after the bus is in the idle state before sending the remote
wake-up resume signaling. This allows the hubs to get into their suspend state and prepare for
propagating resume signaling.
The device has 10ms where it can draw a non-suspend current before it must drive resume signaling.
At the beginning of this period the Link may negate SUSPENDN, allowing the transceiver (and its
oscillator) to power up and stabilize.
Figure 7.7
illustrates the behavior of a device returning to HS mode after being suspended. At T4, a
device that was previously in FS mode would maintain TERMSELECT and XCVRSELECT high.
To generate resume signaling (FS 'K') the device is placed in the "Disable Bit Stuffing and NRZI
encoding" Operational Mode (OPMODE [1:0] = 10), TERMSELECT and XCVRSELECT must be in FS
mode, TXVALID asserted, and all 0's data is presented on the DATA bus for at least 1ms (T1 - T2).
Table 7.8 HS Detection Handshake Timing Values from Suspend
TIMING
PARAMETER
DESCRIPTION
VALUE
T0
While in suspend state an SE0 is detected on the USB. HS
Handshake begins. D+ pull-up enabled, HS terminations
disabled, SUSPENDN negated.
0 (HS Reset T0)
T1
First transition of CLKOUT. CLKOUT "Usable" (frequency
accurate to ±10%, duty cycle accurate to 50±5).
T0 < T1 < T0 + 5.6ms
T2
Device asserts Chirp K on the bus.
T1 < T2 < T0 + 5.8ms
T3
Device removes Chirp K from the bus. (1 ms minimum width)
and begins looking for host chirps.
T2 + 1.0 ms < T3 <
T0 + 7.0 ms
T4
CLK "Nominal" (CLKOUT is frequency accurate to ±500
ppm, duty cycle accurate to 50±5).
T1 < T3 < T0 + 20.0ms
相關PDF資料 |
PDF描述 |
|---|---|
| USB97C201 | USB 2.0 ATA/ ATAPI Controller |
| USB97C201-MC | USB 2.0 ATA/ ATAPI Controller |
| USB97C201-MN | USB 2.0 ATA/ ATAPI Controller |
| USB97CFDC-MN | USB FLOPPY DISK CONTROLLER |
| USB97C202 | ATA/ATAPI CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| USB-3488A | 功能描述:數據記錄與采集 HIGH PERF IEEE-488 USB DAQ GPIB INT CON RoHS:否 制造商:Lantronix 描述/功能:Analog device server 顯示器類型:None 電流額定值: |
| USB3500 | 制造商:SMSC 制造商全稱:SMSC 功能描述:Hi-Speed USB Host, Device or OTG PHY With UTMI+ Interface |
| USB3500-ABZJ | 功能描述:接口 - 專用 USB 2.0 PHY UTMI RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| USB3503 | 制造商:SMSC 制造商全稱:SMSC 功能描述:USB 2.0 HSIC High-Speed Hub Controller Optimized for Portable Applications |
| USB3503A | 制造商:SMSC 制造商全稱:SMSC 功能描述:USB 2.0 HSIC High-Speed Hub Controller Optimized for Portable Applications |
發布緊急采購，3分鐘左右您將得到回復。