- 您現在的位置：買賣IC網 > PDF目錄297644 > UPSD3253B-40T6 (STMICROELECTRONICS) 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP52 PDF資料下載
參數資料
| 型號： | UPSD3253B-40T6 |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP52 |
| 封裝： | PLASTIC, TQFP-52 |
| 文件頁數： | 115/189頁 |
| 文件大小： | 1638K |
| 代理商： | UPSD3253B-40T6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁當前第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁
Obsolete
Product(s)
- Obsolete
Product(s)
UPSD3254A, UPSD3254BV, UPSD3253B, UPSD3253BV
Architecture overview
31/189
The LJMP instruction encodes the destination address as a 16-bit constant. The instruction
is 3 bytes long, consisting of the opcode and two address bytes. The destination address
can be anywhere in the 64K Program Memory space.
The AJMP instruction encodes the destination address as an 11-bit constant. The
instruction is 2 bytes long, consisting of the opcode, which itself contains 3 of the 11 address
bits, followed by another byte containing the low 8 bits of the destination address. When the
instruction is executed, these 11 bits are simply substituted for the low 11 bits in the PC. The
high 5 bits stay the same. Hence the destination has to be within the same 2K block as the
instruction following the AJMP.
In all cases the programmer specifies the destination address to the assembler in the same
way: as a label or as a 16-bit constant. The assembler will put the destination address into
the correct format for the given instruction. If the format required by the instruction will not
support the distance to the specified destination address, a “Destination out of range”
message is written into the List file.
The JMP @A+DPTR instruction supports case jumps. The destination address is computed
at execution time as the sum of the 16-bit DPTR register and the Accumulator. Typically.
DPTR is set up with the address of a jump table. In a 5-way branch, for ex-ample, an integer
0 through 4 is loaded into the Accumulator. The code to be executed might be as follows:
MOV DPTR,#JUMP TABLE
MOV A,INDEX_NUMBER
RL A
JMP @A+DPTR
The RL A instruction converts the index number (0 through 4) to an even number on the
range 0 through 8, because each entry in the jump table is 2 bytes long:
JUMP TABLE:
AJMP CASE 0
AJMP CASE 1
AJMP CASE 2
AJMP CASE 3
AJMP CASE 4
Table 13 shows a single “CALL addr” instruction, but there are two of them, LCALL and
ACALL, which differ in the format in which the subroutine address is given to the CPU. CALL
is a generic mnemonic which can be used if the programmer does not care which way the
address is encoded.
The LCALL instruction uses the 16-bit address format, and the subroutine can be anywhere
in the 64K Program Memory space. The ACALL instruction uses the 11-bit format, and the
subroutine must be in the same 2K block as the instruction following the ACALL.
In any case, the programmer specifies the subroutine address to the assembler in the same
way: as a label or as a 16-bit constant. The assembler will put the address into the correct
format for the given instructions.
Subroutines should end with a RET instruction, which returns execution to the instruction
following the CALL.
RETI is used to return from an interrupt service routine. The only difference between RET
and RETI is that RETI tells the interrupt control system that the interrupt in progress is done.
相關PDF資料 |
PDF描述 |
|---|---|
| UPSD3334D-40U6 | 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PQFP80 |
| US1001FL | 0.5 A, 100 V, SILICON, SIGNAL DIODE |
| US1A-HE3 | 1 A, 50 V, SILICON, SIGNAL DIODE, DO-214AC |
| US1B-HE3 | 1 A, 100 V, SILICON, SIGNAL DIODE, DO-214AC |
| US1G-HE3 | 1 A, 400 V, SILICON, SIGNAL DIODE, DO-214AC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPSD3253B-40T6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3253B-40U1 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3253B-40U1T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3253B-40U6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
| UPSD3253B-40U6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Flash Programmable System Device with 8032 Microcontroller Core |
發布緊急采購，3分鐘左右您將得到回復。