- 您現在的位置：買賣IC網 > PDF目錄383982 > UPD6708CX (NEC Corp.) IEBusa Inter Equipment Busa PROTOCOL CONTROL LSI PDF資料下載
參數資料
| 型號： | UPD6708CX |
| 廠商： | NEC Corp. |
| 英文描述： | IEBusa Inter Equipment Busa PROTOCOL CONTROL LSI |
| 中文描述： | IEBusa設備布薩間協議控制大規模集成電路 |
| 文件頁數： | 30/72頁 |
| 文件大?。?/td> | 292K |
| 代理商： | UPD6708CX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
30
μ
PD6708
5.
COMMUNICATION CONTROL COMMANDS
The operation conditions of the
μ
PD6708 can be controlled by giving it a command from the host controller.
After a communication using the appropriate procedure (see
8.3.2 “Communication control command processing
routine”
), it is executed in a period in which communication is not being performed (standby state).
5.1
Overview of Communication Control Commands
Table 5-1. Overview of Communication Control Commands
Command Name
Description
INIT
(Initialize)
Sets local address and initializes.
SETSA
(Set slave address)
Sets the unit to communicate with.
MREQ1
(Master request 1)
Communicates as a master unit.
MREQ2
(Master request 2)
Continues in previous condition as the master unit and communicates.
ABORT
(Abort)
Aborts communications.
SETSD
(Set slave data)
Sets data for slave transmission.
GETSTA (Get status)
Reads communication status.
SETREV (Set receive)
Sets reception disabled state/enabled state.
(1)
Write command
The command codes and command parameters for the write commands are shown in Table 5-2.
Table 5-2. Command Codes and Command Parameters of Write Commands
Note
Only set when transmitting.
Caution Note that even if the host controller makes a mistake in setting the number of command parameter bytes,
an error message will not be returned by the
μ
PD6708, and command processing will be performed as
though it were a correctly set command.
Command Code
(Lower 4 Bits of
CMR)
Command Parameters (WDB)
Command Name
First Byte
Second Byte
Third Byte
Fourth Byte
INIT
0000
SETSA
0001
MREQ1
0010
MREQ2
0011
ABORT
0100
SETSD
0101
SETREV
0111
Control bits
Broad-
cast bits
Unit address
Condition
setting
code
Slave address
0000
Number of master
transmit data bytes
Note
Master transmit
data (first byte)
Note
Master transmit
data (second byte)
Note
Number of slave
transmit data bytes
Slave transmit
data (first byte)
Slave transmit
data (second byte)
Slave transmit
data (third byte)
Reception status
code
MSB
LSB
MSB
LSB
MSB
LSB
MSB
LSB
MSB
LSB
相關PDF資料 |
PDF描述 |
|---|---|
| UPD6708GS | IEBusa Inter Equipment Busa PROTOCOL CONTROL LSI |
| UPD6951 | 6 BIT D/A CONVERTER FOR VIDEO SIGNAL PROCESSING CMOS LSI |
| UPD6951C | 6 BIT D/A CONVERTER FOR VIDEO SIGNAL PROCESSING CMOS LSI |
| UPD6951G | 6 BIT D/A CONVERTER FOR VIDEO SIGNAL PROCESSING CMOS LSI |
| UPD703130GC-8EU | MOS INTEGRATED CIRCUIT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UPD6708GS | 制造商:NEC 制造商全稱:NEC 功能描述:IEBusa Inter Equipment Busa PROTOCOL CONTROL LSI |
| UPD6708GS(A) | 制造商:Renesas Electronics Corporation 功能描述: |
| UPD67100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASIC |
| UPD67101 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASIC |
| UPD67240 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ASIC |
發布緊急采購，3分鐘左右您將得到回復。