- 您現在的位置：買賣IC網 > PDF目錄372308 > ST623X-KIT 8 MBIT (X8, BLOCK ERASE) FLASH MEMORY PDF資料下載
參數資料
| 型號： | ST623X-KIT |
| 英文描述： | 8 MBIT (X8, BLOCK ERASE) FLASH MEMORY |
| 中文描述： | 入門套件小冊子的ST6230 |
| 文件頁數： | 22/86頁 |
| 文件大?。?/td> | 531K |
| 代理商： | ST623X-KIT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁
22/86
ST62T30B ST62E30B
3.2 RESETS
The MCU can be reset in three ways:
– by the external Reset input being pulled low;
– by Power-on Reset;
– by the digital Watchdog peripheral timing out.
3.2.1 RESET Input
The RESET pin may be connected to a device of
the application board in order to reset the MCU if
required. The RESET pin may be pulled low in
RUN, WAIT or STOP mode. This input can be
used to reset the MCU internal state and ensure a
correct start-up procedure. The pin is active low
and features a Schmitt trigger input. The internal
Reset signal is generated by adding a delay to the
external signal. Therefore even short pulses on
the RESET pin are acceptable, provided V
DD
has
completed its risingphase and that the oscillatoris
running correctly (normal RUN or WAIT modes).
The MCU is kept in the Reset state as long as the
RESET pin is held low.
If RESET activation occurs in the RUN or WAIT
modes, processing of the user program is stopped
(RUN modeonly), the Inputs and Outputs are con-
figured as inputs with pull-up resistors and the
main Oscillator is restarted. When the level on the
RESET pin then goes high, the initialization se-
quence is executed following expiry of the internal
delay period.
If RESET pin activation occurs in the STOP mode,
the oscillator starts up and all Inputs and Outputs
are configured as inputs with pull-up resistors.
When the level of the RESET pin then goes high,
the initialization sequence is executed following
expiry of the internal delay period.
3.2.2 Power-on Reset
The function of the POR circuit consists in waking
up the MCU at an appropriate stage during the
power-on sequence. At the beginning of this se-
quence, the MCU is configured in the Reset state:
all I/O ports are configured as inputs with pull-up
resistors and no instruction is executed. When the
power supply voltage rises to a sufficient level, the
oscillator starts to operate, whereupon an internal
delay is initiated, in order to allow the oscillator to
fully stabilize before executing the first instruction.
The initialization sequence isexecuted immediate-
ly following the internal delay.
The internaldelay isgenerated byan on-chipcoun-
ter. Theinternal reset line is released 2048 internal
clock cycles after release of the external reset.
Notes:
To ensure correct start-up, the user should take
care that the reset signal is not releasedbefore the
V
DD
level is sufficient to allow MCU operation at
the chosen frequency (see Recommended Oper-
ating Conditions).
A proper reset signal for a slow rising V
DD
supply
can generally be provided by an external RC net-
work connected to the RESET pin.
Figure 13. Reset and Interrupt Processing
INNMI MASK SET
( IF PRESENT )
RESET
SELECT
NMI MODE FLAGS
IS RESET STILL
PRESENT
YES
PUT FFEH
ON ADDRESS BUS
FROM RESET LOCATIONS
FFE/FFF
NO
FETCH INSTRUCTION
LOAD PC
VA000427
相關PDF資料 |
PDF描述 |
|---|---|
| ST62T32BB3 | 8-BIT MICROCONTROLLER |
| ST62T32BQ3 | 8-BIT MICROCONTROLLER |
| ST623X-DBE | D/A Converter (D-A) IC; Resolution (Bits):24; Update Rate:192kSPS; No. of DACs:6; Data Interface:Serial; Package/Case:48-LQFP; Leaded Process Compatible:No; No. of Bits:24; No. of Channels:6; Operating Temp. Max:85 C RoHS Compliant: Yes |
| ST623X-EMU2 | REAL TIME EMULATION DEVELOPMENT TOOLS FOR ST6 MCU FAMILY |
| ST62T65BB3 | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST623X-KIT/110 | 功能描述:開發板和工具包 - 其他處理器 ST623X Starter Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| ST623X-KIT/220 | 制造商:STMicroelectronics 功能描述:ST Development Kit, Including ST623X Starter Kit, Development Software CD-ROM, Parallel Cable, Power Supply, Window Development Devices ST62E30BF1, ST (More...) |
| ST623X-KIT/UK | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:STARTER KIT AB 8K BYTE |
| ST-6-24 | 功能描述:XFRMR PWR 115V 12VAC 1.6A RoHS:是 類別:變壓器 >> 功率 系列:ST 標準包裝:1 系列:260 類型:標準 最大功率:65 VA 主線圈:雙 副線圈:三路，中心抽頭 在某電流時的串聯輸出電壓:500 VAC @ 85mA，5 VAC @ 2A，6.3 VAC @ 2A 在某電流時的并聯輸出電壓:- 安裝類型:底座安裝 尺寸/尺寸:102.36mm L x 67.31mm W 高度 - 座高（最大）:66.80mm 端接類型:導線引線 |
| ST6-24 | 制造商:SUPERWORLD 制造商全稱:Superworld Electronics 功能描述:POWER TRANSFORMER |
發布緊急采購，3分鐘左右您將得到回復。