- 您現在的位置：買賣IC網 > PDF目錄1956 > NCN6001DTBR2 (ON Semiconductor)IC INTERFACE SMART CARD 20TSSOP PDF資料下載
參數資料
| 型號： | NCN6001DTBR2 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 5/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC INTERFACE SMART CARD 20TSSOP |
| 標準包裝： | 1 |
| 應用： | 智能卡 |
| 接口： | 微控制器 |
| 電源電壓： | 2.75 V ~ 5.5 V |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | NCN6001DTBR2OSDKR |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
NCN6001
http://onsemi.com
13
Read Register " READ_REG
The READ_REG register contains the data read from the
interface and from the external card. The selected register is
transferred to the MISO pin during the MOSI sequence
(CS = Low). Table 3 gives the bits definition.
Depending upon the programmed SPI_MODE, the
content of READ_REG is transferred on the MISO line
either on the Positive going (SPI_MODE = Special) or upon
the Negative going slope (SPI_MODE = Normal) of the
CLK_SPI signal. The external microcontroller shall discard
the three high bytes since they carry no valid data.
Table 3. MOSI AND MISO BITS IDENTIFICATIONS AND FUNCTIONS
MOSI
b7
b6
b5
b4
b3
b2
b1
b0
Operating Mode
0
1
0
1
0
1
0
1
0
1
0
RST
CLK
I/O
VCC
C4
VCC
C8
Asynchronous, Program Chip
Synchronous, Sets Card Bits
MISO
z
Card Detect
I/O
C4
C8
PWR Monitor
Read Back Data
ASYNCHRONOUS MODE
In this mode, the CRD_C4 and CRD_C8 pins are used to
define the physical addresses of the interfaces when a bank
of up to four NCN6001 share the same digital bus.
SYNCHRONOUS MODE
In this mode, CRD_C4 and CRD_C8 are connected to the
smart card and it is no longer possible to share the CS signal
with other device. Consequently, a dedicated Chip Select
signal must be provided when the interfaces operate in a
multiple operation mode (Figure 34).
On the other hand, since bits [b4 – b0] of the MOSI
register contain the smart card data, programming the
CRD_VCC output voltage shall be done by sending a
The CRD_RST pin reflects the content of the MOSI
WRT_REG[b4] during the chip programming sequence.
Since this bit shall be Low to address the internal register of
the chip, care must be observed as this signal will be
immediately transferred to the CRD_RST pin.
Since no physical address can exist when the chip operates
in this mode, the MOSI register must use the format
%100XXXXX to program the chip (%100 prefix, XXXXX
data).
Example:
LDAA #%10010111
;set RST = H, CLK = 1/1, VCC = 5.0 V
STAA MOSI
LDAA #%11010011
;SYNC. Card: set RST = H, CLK = L, IO = L, C4 = H, C8= H
STAA MOSI
LDAA #%00111110
;ASYNC. Card: set RST = H, CLK =
, VCC = 3.0 V
STAA MOSI
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6004AFTBR2G | IC INTERFACE SAM/SIM DUAL 48TQFP |
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
| NCN8024RDWR2G | IC SMART CARD IC2 28SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6001DTBR2G | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6001MUTWG | 制造商:ON Semiconductor 功能描述:ANA COMPACT SMARTCARD IC - Tape and Reel 制造商:ON Semiconductor 功能描述:IC INTERFACE SMART CARD 制造商:ON Semiconductor 功能描述:REEL - ANA COMPACT SMARTCARD IC |
| NCN6004A | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit |
| NCN6004A/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit |
| NCN6004A_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit |
發布緊急采購，3分鐘左右您將得到回復。