- 您現在的位置：買賣IC網 > PDF目錄1956 > NCN6001DTBR2 (ON Semiconductor)IC INTERFACE SMART CARD 20TSSOP PDF資料下載
參數資料
| 型號： | NCN6001DTBR2 |
| 廠商： | ON Semiconductor |
| 文件頁數： | 31/36頁 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 20TSSOP |
| 標準包裝： | 1 |
| 應用： | 智能卡 |
| 接口： | 微控制器 |
| 電源電壓： | 2.75 V ~ 5.5 V |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 標準包裝 |
| 安裝類型： | 表面貼裝 |
| 其它名稱： | NCN6001DTBR2OSDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁
NCN6001
http://onsemi.com
4
PIN FUNCTIONS AND DESCRIPTION
TSSOP LLGA
Name
Type
Description
1
18
I/O
Input/Output
Pullup
This pin is connected to an external microcontroller interface. A bidirectional level
translator adapts the serial I/O signal between the smart card and the microcontroller.
The level translator is enabled when CS = L, the sub address has been selected and
the system operates in the Asynchronous mode. When a Synchronous card is in use,
this pin is disconnected and the data and the transaction take place with the MISO b3
register.
The internal pullup resistor connected on the mC side is activated and visible by the
selected chip only.
2
19
INT
OUTPUT
Pullup
This pin is activated LOW when a card has been inserted and detected by CRD_DET
pin. Similarly, an interrupt is generated when the CRD_VCC output is overloaded, or
when the card has been extracted whatever be the transaction status (running or
standby).
The INT signal is reset to High according to Table 7 and Figure 11. On the other hand,
the pin is forced to a logic High when the input voltage VCC drops below 2.0 V.
3
20
CLK_IN
CLOCK
INPUT
High
impedance
The builtin Schmitt trigger receiver makes this pin suitable for a large type of clock
signal (Figure 30). This pin can be connected to either the microcontroller master
clock, or to a crystal signal, to drive the external smart cards. The signal is fed to the
internal clock selector circuit and translated to the CRD_CLK pin at either the same
frequency, or divided by 2 or 4, depending upon the programming mode.
Note: The chip guarantees the EMV 50% Duty Cycle when the clock divider ratio is
1/2 or 1/4, even when the CLK_IN signal is out of the 45% to 55% range specified by
ISO and EMV specifications.
Care must be observed, at PCB level, to minimize the pickup noise coming from the
CLK_IN line.
4
1
MOSI
INPUT
Master Out Slave In: SPI Data Input from the external microcontroller. This byte
contents the address of the selected chip among the four possible, together with the
programming code for a given interface.
5
2
CLK_SPI
INPUT
Clock Signal to synchronize the SPI data transfer. The builtin Schmitt trigger receiver
makes this pin compatible with a wide range of input clock signal (Figure 30). This
clock is fully independent from the CLK_IN signal and does not play any role with the
data transaction.
6
3
EN_RPU
INPUT, Logic
This pin is used to activate the I/O internal pullup resistor according to the here below
true table:
EN_RPU = Low I/O Pullup resistor disconnected
EN_RPU = High I/O Pullup resistor connected
When two or more NCN6001 chips shares the same I/O bus, one chip only shall have
the internal pullup resistor enabled to avoid any overload of the I/O line.
Moreover, when Asynchronous and Synchronous cards are handled by the interfaces,
the activated I/O pullup resistor must preferably be the one associated with the
Asynchronous circuit
.
On the other hand, since no internal pullup bias resistor is built in the chip, pin 6 must
be connected to the right voltage level to make sure the logic function is satisfied.
7
4
MISO
OUTPUT
Master In Slave Out: SPI Data Output from the NCN6001. This byte carries the state
of the interface, the serial transfer being achieved according to the programmed mode
(Table 2), using the same CLK_SPI signal and during the same MOSI time frame. The
three high bits [b7:b5] have no meaning and shall be discarded by the microcontroller.
An external 4.7 kW Pull down resistor might be necessary to avoid misunderstanding
of the pin 7 voltage during the High Z state.
8
5
CS
INPUT
This pin synchronizes the SPI communication and provides the chip address and
selected functions.
All the NCN6001 functions, both programming and card transaction, are disabled
when CS = H.
9
6
VCC
POWER
This pin is connected to the NCN6001 supply voltage and must be bypassed to
ground by a 10 mF/6.0 V capacitor.
Since tantalum capacitors have relative high ESR, using low ESR ceramic type
(MURATA X5R, Resr < 100 mW) is highly recommended.
相關PDF資料 |
PDF描述 |
|---|---|
| NCN6004AFTBR2G | IC INTERFACE SAM/SIM DUAL 48TQFP |
| NCN6804MNR2G | IC SMART CARD DUAL W/SPI 32-QFN |
| NCN7200MTTWG | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
| NCN8024RDWR2G | IC SMART CARD IC2 28SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN6001DTBR2G | 功能描述:輸入/輸出控制器接口集成電路 2.7V POS/ATM Smart Card Interface RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| NCN6001MUTWG | 制造商:ON Semiconductor 功能描述:ANA COMPACT SMARTCARD IC - Tape and Reel 制造商:ON Semiconductor 功能描述:IC INTERFACE SMART CARD 制造商:ON Semiconductor 功能描述:REEL - ANA COMPACT SMARTCARD IC |
| NCN6004A | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit |
| NCN6004A/D | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit |
| NCN6004A_06 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Dual SAM/SIM Interface Integrated Circuit |
發布緊急采購，3分鐘左右您將得到回復。