- 您現在的位置：買賣IC網 > PDF目錄1954 > MCZ33797EKR2 (Freescale Semiconductor)IC SQUIB DRIVER 2CHAN 32-SOIC PDF資料下載
參數資料
| 型號： | MCZ33797EKR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 21/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SQUIB DRIVER 2CHAN 32-SOIC |
| 標準包裝： | 1,000 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 32-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 32-SOIC |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
33797
FUNCTIONAL DEVICE OPERATION
PROTECTION AND DIAGNOSIS FEATURES
indicated as a short, and a loss of the connection between the
VDIAG_X pin and the VFIRE_XX pin will be indicated as an
open. Any external capacitance on the VFIRE_XX pin will
affect the time needed to settle to an accurate value.
HIGH SIDE SAFING SENSOR DIAGNOSTIC DATA
RESULTS
If the VFIRE_XX pin is shorted to the VDIAG_X pin, the
RSSLO bit will be set to “0” and the RSSHI bit will be set to
“0”. If the VFIRE_XX pin has no connection to the VDIAG_X
pin, the RSSLO bit will be set to “1” and the RSSHI bit will be
set to “1”. Standard operation with a safing sensor resistor will
have the RSSHI bit set to “0” and the RSSLO bit set to “1”.
FIRING SUPPLY VOLTAGE (VDIAG_X)
DIAGNOSTICS ($C0 COMMAND)
This function monitors the voltage on the VDIAG_X pin. The
supply voltage is compared to two thresholds (nominal and
minimum) and will provide two bits of data to indicate if the pin
voltage is above, below, or in between the predetermined
threshold levels. There is one diagnostic circuit for each
VDIAG_X pin.
VDIAG_X SUPPLY VOLTAGE DIAGNOSTIC DATA
RESULTS
If the VDIAG_X voltage is above the high limit, bits VDHI and
VDLO will both be set to “1”. If the VDIAG_X voltage is
between the high limit and the low limit, bit VDHI will be set to
“0” and VDLO will be set to “1”. If the VDIAG_X voltage is
below the low limit, bits VDHI and VDLO will both be set to
“0”.
FIRING SUPPLY VOLTAGE (VFIRE_XX)
DIAGNOSTICS ($C5 COMMAND)
This function monitors the voltage on the VFIRE_XX pin. The
supply voltage is compared to two thresholds (nominal and
minimum) and will provide two bits of data to indicate if the pin
voltage is above, below, or in between the predetermined
threshold levels. There is one diagnostic circuit for each
VFIRE_XX pin.
VFIRE_XX SUPPLY VOLTAGE DIAGNOSTIC DATA
RESULTS
If the VFIRE_XX voltage is above the high limit, bits VFHI and
VFLO will both be set to “1”. If the VFIRE_XX voltage is
between the high limit and the low limit, bit VFHI will be set to
“0” and VFLO will be set to “1”. If the VFIRE_XX voltage is
below the low limit, bits VFHI and VFLO will both be set to “0”.
FIRING SUPPLY VOLTAGE DIAGNOSTICS,
VDIAG_X V1, V2, V3, V4 ($C6 COMMAND)
The VDIAG_X V1, V2, V3, V4 function monitors voltage on
the VDIAG pins. The voltage being measured is then
compared to four thresholds and will provide four bits of data
to indicate if the pin voltage is above, below, or between the
predetermined threshold levels. There is one diagnostic
circuit for each VDIAG_X pin.
VDIAG_X VOLTAGE DIAGNOSTIC DATA RESULTS
If the VDIAG_X voltage is above the threshold limit, the
VDIAG_X VX bit will be set to “1”. If the VDIAG_X voltage is
below the threshold limit, the VDIAG_X VX bit will be set to
“0”.
VFIRE_RTN DIAGNOSTICS ($C9 COMMAND)
This function monitors the resistance on the VFIRE_RTN pin
for open pin connections. The VFIRE_RTN voltage is
compared to a threshold to determine if the VFIRE_RTN pin
connection between the pin and the printed circuit board is
shorted or open.
VFIRE_RTN DIAGNOSTIC DATA RESULTS
If the VFIRE_RTN pin is above the threshold limit (open), the
VFIRE_RTN X VFXLOW will be set to “1”. If the VFIRE_RTN
pin is below the threshold limit (shorted), the VFIRE_RTN X
VFXLOW will be set to “0”.
VFIRE return tests are disabled during firing.
DESIGN NOTES
For all standard or cross-coupled squib IC configurations, the
SQB_LO_XX pin must be tied to a SENSE_XX pin for either
squib IC #1 or squib IC #2 (see Figure 6 and Figure 8).
An active 600
A current sink is located in the SENSE_XX
pin. The sink current is used to pull the charge off the external
EMC/filter caps after a diagnostic measurement has been
made.
SQUIB SHORT-TO-BATTERY/GROUND
DIAGNOSTICS ($C1 COMMAND)
This function monitors the voltage on the SENSE_XX pins.
The voltage is compared to two thresholds (minimum and
maximum) and will provide two bits of data to indicate if the
pin voltage is above, below, or in between the predetermined
threshold levels.
When enabled, a 2.7 mA current source located in the
SQB_HI_XX pin is activated, sourcing current from the
SQB_HI_XX to the SENSE_XX pin. When resistive
measurement legs to comparators located in the SENSE_XX
pin are activated, a fault on either side of the squib can be
easily detected. An external current path that causes the
SQB_LO_XX, SQB_HI_XX, or SENSE_XX pin to be pulled
below the minimum threshold, will be indicated as a “Short to
Ground”.
If the SQB_LO_XX, SQB_HI_XX, or SENSE_XX pin has an
external current path that causes the pin to be pulled above
the maximum threshold, a “Short to Battery” will be indicated.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33884EG | IC MULTIPLE CONTACT MON 24-SOIC |
| MCZ33905BD3EK | IC SBC CAN HS 3.3V 54SOIC |
| MCZ33972EWR2 | IC SWITCH DETECTION MULT 32-SOIC |
| MCZ33975AEKR2 | IC SWITCH DETECT MULT ENH 32SOIC |
| MCZ33993EWR2 | IC MULTIPLE SWITCH DETECT 32SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33800EK | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
發布緊急采購，3分鐘左右您將得到回復。