- 您現在的位置：買賣IC網 > PDF目錄1954 > MCZ33797EKR2 (Freescale Semiconductor)IC SQUIB DRIVER 2CHAN 32-SOIC PDF資料下載
參數資料
| 型號： | MCZ33797EKR2 |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 10/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SQUIB DRIVER 2CHAN 32-SOIC |
| 標準包裝： | 1,000 |
| 系列： | * |
| 應用： | * |
| 接口： | * |
| 電源電壓： | * |
| 封裝/外殼： | 32-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 32-SOIC |
| 包裝： | 帶卷 (TR) |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Analog Integrated Circuit Device Data
18
Freescale Semiconductor
33797
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
SQUIB SENSE XX (SENSE_XX)
The Sense pins are used exclusively for diagnostics related
to the squib, driver FETs, or harness. Commands using the
Sense pins include:
C1, C2, C3, C9
D<3:0>
E<3:0>
E9
82/1x
83/2x
Independent of the system configuration, normal or cross
coupled, the Sense pin, xx and SquibHi, xx of a single IC are
always connected to the same squib with the SquibHi pin
connected to the high pin of the squib and the Sense pin
connected to the low pin of the squib. A cross coupled
configuration is achieved by only cross coupling the squib low
STANDARD APPLICATIONS
In the standard mode, the $C2 (SQUIB_LO_XX_CONT)
command will be used to check continuity of the low side
driver from the SQB_LO_XX pin to the high side driver FET
(see Figure 6).
CROSS-COUPLED APPLICATIONS
Used during cross-coupling applications involving two four
channel squib driver ICs (squib driver IC #1 and squib driver
IC #2). SENSE_XX pins from squib driver IC #1 are
connected to their respective squib minus pins (Squib Low/
SQB_LO_XX) from squib driver IC #2 (Figure 8).
SENSE_XX pins are used to feed diagnostic signals back to
squib driver IC #1 for determining squib resistance, short-to-
battery/ground, and squib loop-to-loop short conditions.
During a fire event, the fire current passes from squib driver
IC #1 high side driver though the squib to squib driver IC #2
low side driver (Figure 8). In the cross-coupled mode, the
squib driver IC #2 $C2 (SQUIB_LO_XX_CONT) command
will be used to check continuity of the low side driver from the
SQB_LO_XX pin to the low side driver FET.
DESIGN NOTES
Diagnostics always have the form of a forcing function and a
measurement or sense function. In a cross couple
configuration, most diagnostics are unaffected and are single
commands except for $C2 Low Side FET Continuity and
$E<3:0> Harness Shorts, and 83/2x Low Side FET test. This
command must be sent to each IC to be executed. For these
three diagnostics, two commands are required because the
forcing function and sensing function are on separate ICs.
Harness Shorts Diagnostics: Force using $E<3:0> on IC#1,
Sense $E8 on IC2
Low Side FET Continuity: Force using $C1 on IC#1, Sense
using $C2 on IC#2
Low Side FET Test: Force using $C1 on IC#1, Sense using
$C2 on IC#2
An active 600
A current sink is located in the SENSE_XX
pin. The sink current is used to pull the charge off of the
external EMC/filter caps after a diagnostic measurement has
been made.
SQUIB HI XX (SQB_HI_XX)
Squib high pins for squibs 1A, 1B, 2A, and 2B. These pins are
connected to the sources of the high side FET drivers, as well
as the diagnostic circuitry.
SQUIB LOW XX (SQB_LO_XX)
Squib low pins for squibs 1A, 1B, 2A, and 2B. These pins are
connected to the drains of the low side FET drivers, as well
as the diagnostic circuitry.
SQUIB FIRING SUPPLY XX (VFIRE_XX)
Firing supply pins for squibs 1A, 1B, 2A, and 2B. These pins
are connected to the drains of the high side FET drivers.
Feedback for high side safing for squibs 1A and 1B will be
referenced from VFIRE_1A and squibs 2A and 2B from
VFIRE_2A. For high side safing, VFIRE_1B should be
connected to VFIRE_1A pin and VFIRE_2B to VFIRE_2A
pin.
SQUIB FIRE POWER GROUND (VFIRE_RTN)
Return for squibs 1A, 1B, 2A AND 2B. The pins are tied to the
source pins of both low side FET drivers, as well as the
diagnostic circuitry. The RTN pins are tied internally.
相關PDF資料 |
PDF描述 |
|---|---|
| MCZ33884EG | IC MULTIPLE CONTACT MON 24-SOIC |
| MCZ33905BD3EK | IC SBC CAN HS 3.3V 54SOIC |
| MCZ33972EWR2 | IC SWITCH DETECTION MULT 32-SOIC |
| MCZ33975AEKR2 | IC SWITCH DETECT MULT ENH 32SOIC |
| MCZ33993EWR2 | IC MULTIPLE SWITCH DETECT 32SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MCZ33800EK | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG Control IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800EKR2 | 功能描述:馬達/運動/點火控制器和驅動器 AUTO ENG CONTROL IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33800R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Engine Control Integrated Circuit |
| MCZ33810EK | 功能描述:馬達/運動/點火控制器和驅動器 Ignition Injector Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MCZ33810EK/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Automotive Engine Control IC |
發布緊急采購，3分鐘左右您將得到回復。