- 您現在的位置：買賣IC網 > PDF目錄299463 > MBM29DL163TD12PBT (FUJITSU LTD) 1M X 16 FLASH 3V PROM, 120 ns, PBGA48 PDF資料下載
參數資料
| 型號： | MBM29DL163TD12PBT |
| 廠商： | FUJITSU LTD |
| 元件分類： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 120 ns, PBGA48 |
| 封裝： | PLASTIC, FBGA-48 |
| 文件頁數： | 50/76頁 |
| 文件大?。?/td> | 1146K |
| 代理商： | MBM29DL163TD12PBT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
MBM29DL16XTD/BD-70/90/12
54
Sector Erase
Sector erase is a six bus cycle operation. There are two “unlock” write cycles. These are followed by writing the
“set-up” command. Two more “unlock” write cycles are then followed by the Sector Erase command. The sector
address (any address location within the desired sector) is latched on the falling edge of CE or WE whichever
happens later, while the command (Data = 30H) is latched on the rising edge of CE or WE which happens first.
After time-out of “tTOW” from the rising edge of the last sector erase command, the sector erase operation will begin.
Multiple sectors may be erased concurrently by writing the six bus cycle operations on Table 12. This sequence
is followed with writes of the Sector Erase command to addresses in other sectors desired to be concurrently
erased. The time between writes must be less than “tTOW” otherwise that command will not be accepted and
erasure will start. It is recommended that processor interrupts be disabled during this time to guarantee this
condition. The interrupts can be re-enabled after the last Sector Erase command is written. A time-out of “tTOW”
from the rising edge of last CE or WE whichever happens first will initiate the execution of the Sector Erase
command(s). If another falling edge of CE or WE, whichever happens first occurs within the “tTOW” time-out
window the timer is reset. (Monitor DQ3 to determine if the sector erase timer window is still open, see section
DQ3, Sector Erase Timer.) Any command other than Sector Erase or Erase Suspend during this time-out period
will reset the devices to the read mode, ignoring the previous command string. Resetting the devices once
execution has begun will corrupt the data in the sector. In that case, restart the erase on those sectors and allow
them to complete. (Refer to the Write Operation Status section for Sector Erase Timer operation.) Loading the
sector erase buffer may be done in any sequence and with any number of sectors (0 to 38).
Sector erase does not require the user to program the devices prior to erase. The devices automatically program
all memory locations in the sector(s) to be erased prior to electrical erase (Preprogram function). When erasing
a sector or sectors the remaining unselected sectors are not affected. The system is not required to provide any
controls or timings during these operations.
The system can determine the status of the erase operation by using DQ7 (Data Polling), DQ6 (Toggle Bit), or
RY/BY.
The sector erase begins after the “tTOW” time out from the rising edge of CE or WE whichever happens first for
the last sector erase command pulse and terminates when the data on DQ7 is “1” (See Write Operation Status
section.) at which time the devices return to the read mode. Data polling and Toggle Bit must be performed at
an address within any of the sectors being erased.
Multiple Sector Erase Time; [Sector Erase Time + Sector Program Time (Preprogramming)]
× Number of Sector
Erase
In case of multiple sector erase across bank boundaries, a read from bank (read-while-erase) can not performe.
Figure 23 illustrates the Embedded EraseTM Algorithm using typical command strings and bus operations.
Erase Suspend/Resume
The Erase Suspend command allows the user to interrupt a Sector Erase operation and then perform data reads
from or programs to a sector not being erased. This command is applicable ONLY during the Sector Erase
operation which includes the time-out period for sector erase. The Erase Suspend command will be ignored if
written during the Chip Erase operation or Embedded Program Algorithm. Writting the Erase Suspend command
(B0H) during the Sector Erase time-out results in immediate termination of the time-out period and suspension
of the erase operation.
Writing the Erase Resume command (30H) resumes the erase operation. The bank addresses of sector being
erasing or suspending should be set when writting the Erase Suspend or Erase Resume command.
When the Erase Suspend command is written during the Sector Erase operation, the device will take a maximum
of “tSPD” to suspend the erase operation. When the devices have entered the erase-suspended mode, the
相關PDF資料 |
PDF描述 |
|---|---|
| MBM29DL32TF70TN | 2M X 16 FLASH 3V PROM, 70 ns, PDSO48 |
| MBM29F800TA-70PFTN-E1 | 512K X 16 FLASH 5V PROM, 70 ns, PDSO48 |
| MBR-2051-1B5T | 51 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A1T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
| MBR-2069-0A2T | 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MBM29DL163TD-70PBT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-70PFTN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-70PFTR | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-90PBT | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
| MBM29DL163TD-90PFTN | 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation |
發布緊急采購，3分鐘左右您將得到回復。