參數(shù)資料
型號: MBM29DL163TD12PBT
廠商: FUJITSU LTD
元件分類: PROM
英文描述: 1M X 16 FLASH 3V PROM, 120 ns, PBGA48
封裝: PLASTIC, FBGA-48
文件頁數(shù): 38/76頁
文件大小: 1146K
代理商: MBM29DL163TD12PBT
MBM29DL16XTD/BD-70/90/12
43
Standby Mode
There are two ways to implement the standby mode on the MBM29DL16XTD/BD devices, one using both the
CE and RESET pins; the other via the RESET pin only.
When using both pins, a CMOS standby mode is achieved with CE and RESET inputs both held at VCC ± 0.3 V.
Under this condition the current consumed is less than 5
A max. During Embedded Algorithm operation, VCC
active current (ICC2) is required even CE = “H”. The device can be read with standard access time (tCE) from either
of these standby modes.
When using the RESET pin only, a CMOS standby mode is achieved with RESET input held at VSS ± 0.3 V (CE
= “H” or “L”). Under this condition the current is consumed is less than 5
A max. Once the RESET pin is taken
high, the device requires tRH of wake up time before outputs are valid for read access.
In the standby mode the outputs are in the high impedance state, independent of the OE input.
Automatic Sleep Mode
There is a function called automatic sleep mode to restrain power consumption during read-out of
MBM29DL16XTD/BD data. This mode can be used effectively with an application requested low power
consumption such as handy terminals.
To activate this mode, MBM29DL16XTD/BD automatically switch themselves to low power mode when
MBM29DL16XTD/BD addresses remain stably during access fine of 150 ns. It is not necessary to control CE,
WE, and OE on the mode. Under the mode, the current consumed is typically 1
A (CMOS Level).
During simultaneous operation, VCC active current (ICC2) is required.
Since the data are latched during this mode, the data are read-out continuously. If the addresses are changed,
the mode is canceled automatically and MBM29DL16XTD/BD read-out the data for changed addresses.
Output Disable
With the OE input at a logic high level (VIH), output from the devices are disabled. This will cause the output pins
to be in a high impedance state.
Autoselect
The autoselect mode allows the reading out of a binary code from the devices and will identify its manufacturer
and type. This mode is intended for use by programming equipment for the purpose of automatically matching
the devices to be programmed with its corresponding programming algorithm. This mode is functional over the
entire temperature range of the devices.
To activate this mode, the programming equipment must force VID (11.5 V to 12.5 V) on address pin A9. Two
identifier bytes may then be sequenced from the devices outputs by toggling address A0 from VIL to VIH. All
addresses are DON’T CARES except A0, A1, and A6 (A-1). (See Tables 3 and 4.)
The manufacturer and device codes may also be read via the command register, for instances when the
MBM29DL16XTD/BD are erased or programmed in a system without access to high voltage on the A9 pin. The
command sequence is illustrated in Table 12. (Refer to Autoselect Command section.)
相關PDF資料
PDF描述
MBM29DL32TF70TN 2M X 16 FLASH 3V PROM, 70 ns, PDSO48
MBM29F800TA-70PFTN-E1 512K X 16 FLASH 5V PROM, 70 ns, PDSO48
MBR-2051-1B5T 51 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG
MBR-2069-0A1T 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG
MBR-2069-0A2T 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG
相關代理商/技術參數(shù)
參數(shù)描述
MBM29DL163TD-70PBT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-70PFTN 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-70PFTR 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-90PBT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-90PFTN 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation