參數資料
型號： MBM29DL163TD12PBT
廠商： FUJITSU LTD
元件分類： PROM
英文描述： 1M X 16 FLASH 3V PROM, 120 ns, PBGA48
封裝： PLASTIC, FBGA-48
文件頁數： 43/76頁
文件大小： 1146K
代理商： MBM29DL163TD12PBT
MBM29DL16XTD/BD-70/90/12
48
Write
Device erasure and programming are accomplished via the command register. The contents of the register serve
as inputs to the internal state machine. The state machine outputs dictate the function of the device.
The command register itself does not occupy any addressable memory location. The register is a latch used to
store the commands, along with the address and data information needed to execute the command. The
command register is written by bringing WE to VIL, while CE is at VIL and OE is at VIH. Addresses are latched on
the falling edge of WE or CE, whichever happens later; while data is latched on the rising edge of WE or CE,
whichever happens first. Standard microprocessor write timings are used.
Refer to AC Write Characteristics and the Erase/Programming Waveforms for specific timing parameters.
Sector Group Protection
The MBM29DL16XTD/BD feature hardware sector group protection. This feature will disable both program and
erase operations in any combination of seventeen sector groups of memory. (See Tables 9.1 and 9.2). The sector
group protection feature is enabled using programming equipment at the user’s site. The device is shipped with
all sector groups unprotected.
To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE, (suggest
VID = 11.5 V), CE = VIL and A0 = A6 = VIL, A1 = VIH. The sector group addresses (A19, A18, A17, A16, A15, A14, A13,
and A12) should be set to the sector to be protected. Tables 5.1 to 8.2 define the sector address for each of the
thirty nine (39) individual sectors, and tables 9.1 and 9.2 define the sector group address for each of the seventeen
(17) individual group sectors. Programming of the protection circuitry begins on the falling edge of the WE pulse
and is terminated with the rising edge of the same. Sector group addresses must be held constant during the
WE pulse. See Figures 18 and 26 for sector group protection waveforms and algorithm.
To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9
with CE and OE at VIL and WE at VIH. Scanning the sector group addresses (A19, A18, A17, A16, A15, A14, A13, and
A12) while (A6, A1, A0) = (0, 1, 0) will produce a logical “1” code at device output DQ0 for a protected sector.
Otherwise the device will produce “0” for unprotected sector. In this mode, the lower order addresses, except
for A0, A1, and A6 are DON’T CARES. Address locations with A1 = VIL are reserved for Autoselect manufacturer
and device codes. A-1 requires to apply to VIL on byte mode.
It is also possible to determine if a sector group is protected in the system by writing an Autoselect command.
Performing a read operation at the address location XX02H, where the higher order addresses (A19, A18, A17,
A16, A15, A14, A13, and A12) are the desired sector group address will produce a logical “1” at DQ0 for a protected
sector group. See Tables 11.1 to 11.8 for Autoselect codes.
Temporary Sector Group Unprotection
This feature allows temporary unprotection of previously protected sector groups of the MBM29DL16XTD/BD
devices in order to change data. The Sector Group Unprotection mode is activated by setting the RESET pin to
high voltage (VID). During this mode, formerly protected sector groups can be programmed or erased by selecting
the sector group addresses. Once the VID is taken away from the RESET pin, all the previously protected sector
groups will be protected again. Refer to Figures 19 and 27.
相關PDF資料
PDF描述
MBM29DL32TF70TN 2M X 16 FLASH 3V PROM, 70 ns, PDSO48
MBM29F800TA-70PFTN-E1 512K X 16 FLASH 5V PROM, 70 ns, PDSO48
MBR-2051-1B5T 51 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG
MBR-2069-0A1T 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG
MBR-2069-0A2T 69 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER, PLUG
相關代理商/技術參數
參數描述
MBM29DL163TD-70PBT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-70PFTN 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-70PFTR 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-90PBT 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
MBM29DL163TD-90PFTN 制造商:SPANSION 制造商全稱:SPANSION 功能描述:FLASH MEMORY CMOS 16M (2M X 8/1M X 16) BIT Dual Operation
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*