- 您現在的位置：買賣IC網 > PDF目錄370849 > M37736EHBGS (Mitsubishi Electric Corporation) PROM VERSION OF M37736EHBXXXGP PDF資料下載
參數資料
| 型號： | M37736EHBGS |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | PROM VERSION OF M37736EHBXXXGP |
| 中文描述： | PROM的版本M37736EHBXXXGP |
| 文件頁數： | 24/96頁 |
| 文件大?。?/td> | 1328K |
| 代理商： | M37736EHBGS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
MITSUBISHI MICROCOMPUTERS
M37736MHBXXXGP
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
24
(4) Pulse width modulation mode [11]
Figure 26 shows the bit configuration of the timer Ai mode register
during the pulse width modulation mode. In the pulse width modulation
mode, bits 0, 1, and 2 must be set to “1”.
Bit 5 is used to determine whether to perform as the 16-bit length
pulse width modulator or the 8-bit length pulse width modulator. 16-
bit length pulse width modulator is selected when bit 5 is “0” and 8-bit
length pulse width modulator is selected when bit 5 is “1”. The 16-bit
length pulse width modulator is described first.
The pulse width modulator can be started with a software trigger or
with an input signal from a TAi
IN
pin (external trigger).
The software trigger mode is selected when bit 4 is “0”. Pulse width
modulator is started and pulse is output from the TAi
OUT
pin when
the timer Ai start flag is set to “1”.
The external trigger mode is selected when bit 4 is “1”. Pulse width
modulator starts when a trigger signal is input from the TAi
IN
pin when
the timer Ai start flag is “1”. Whether to trigger at the fall or rise of the
trigger signal is determined by bit 3. The trigger is at the fall of the
trigger signal when bit 3 is “0” and at the rise when it is “1”.
When data is written to timer Ai with the pulse width modulator halted,
it is written to the reload register and the counter.
Then when the timer Ai start flag is set to “1” and a software trigger or
an external trigger is issued to start modulation, the waveform shown
in Figure 27 is output continuously. Once modulation is started,
triggers are not accepted. When the value in the reload register is m,
the duration “H” of pulse is
The reload register and the counter are both divided into 8-bit halves.
The low-order 8 bits function as a prescaler and the high-order 8 bits
function as the 8-bit length pulse width modulator. The prescaler
counts the clock selected by bits 6 and 7. A pulse is generated when
the counter reaches 0000
16
as shown in Figure 28. At the same time,
the contents of the reload register is transferred to the counter, and
count is continued.
Fig. 26 Timer Ai mode register bit configuration during pulse width
modulation mode
An interrupt request signal is generated and the interrupt request bit
of the timer Ai interrupt control register is set at each fall of the output
pulse.
The width of the output pulse is changed by updating timer data. The
update can be performed at any time. The output pulse width is
changed at the rise of the pulse after data is written to the timer.
The contents of the reload register is transferred to the counter just
before the rise of the next output pulse so that the pulse width is
changed from the next output pulse.
Undefined data is read when timer Ai is read.
The 8-bit length pulse width modulator is described next.
The 8-bit length pulse width modulator is selected when bit 5 of the
timer Ai mode register is “1”.
1
selected clock frequency
m
and the output pulse period is
1
selected clock frequency
(2
16
– 1).
7 6 5 4 3 2 1 0
1 1
1
Timer A0 mode register 56
16
Timer A1 mode register 57
16
Timer A2 mode register 58
16
Timer A3 mode register 59
16
Timer A4 mode register 5A
16
Addresses
1 : Always “1” in pulse width
modulation mode
0
:
Software trigger
1 0
: Trigger at the falling of TAi
I
N
input
1 1 : Trigger at the rising of TAi
IN
input
Clock source selection bit
0 0 : Select f
2
0 1 : Select f
16
1 0 : Select f
64
1 1 : Select f
512
1 1 : Always “11” in pulse width
modulation mode
0 : 16 bit pulse width modulator
1 : 8 bit pulse width modulator
相關PDF資料 |
PDF描述 |
|---|---|
| M37736EHLXXXHP | PROM VERSION OF M37736MHLXXXHP(MICROCOMPUTERS) |
| M37736MHLXXXHP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37736EHBXXXGP | PROM VERSION OF M37736MHBXXXGP(MICROCOMPUTERS) |
| M37736MHBXXXGP | SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37753FFCFP | SINGLE CHIP 16 BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37736EHBXXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736MHBXXXGP(MICROCOMPUTERS) |
| M37736EHL | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37736MHLXXXHP(MICROCOMPUTERS) |
| M37736EHLXXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:PROM VERSION OF M37736MHLXXXHP |
| M37736M4B | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37736M4BXXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。