- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4110EUHF#TR (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 PDF資料下載
參數資料
| 型號： | LTC4110EUHF#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| 封裝： | 5 X 7 MM, 0.75 MM HEIGHT, PLASTIC, MO-220WHKD, QFN-38 |
| 文件頁數： | 28/52頁 |
| 文件大?。?/td> | 450K |
| 代理商： | LTC4110EUHF#TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
LTC4110
34
4110fb
SOFT-START
The LTC4110 is soft-started with the 0.1μF capacitor on
the ITH pin. On start-up, the ITH pin voltage will rise quickly
to 0.1V, then ramp up at a rate set by the internal 24μA
pull-up current and the external capacitor. Battery charging
current starts ramping up when ITH voltage reaches 0.7V
and full current is achieved with ITH at about 2V. With a
0.1μF capacitor, time to reach full charge current is about
8ms and it is assumed that input voltage to the charger
will reach full value in less than 8ms. The capacitor can
be increased up to 1μF if longer input start-up times are
needed.
In any switching regulator, conventional timer-based soft-
starting can be defeated if the input voltage rises much
slower than the timeout period. This happens because
the switching regulators in the battery charger and the
computer power supply are typically supplying a xed
amount of power to the load. If input voltage comes up
slowly compared to the soft-start time, the regulators will
try to deliver full power to the load when the input voltage
is still well below its nal value. If the adapter is current
limited, it cannot deliver full power at reduced output
voltages and the possibility exists for a quasi “l(fā)atch” state
where the adapter output stays in a current limited state at
reduced output voltage. For instance, if maximum charger
plus computer load power is 30W, a 15V adapter might
be current limited at 2.5A. If adapter voltage is less than
(30W/2.5A = 12V) when full power is drawn, the adapter
voltage will be pulled down by the constant 30W load
until it reaches a lower stable state where the switching
regulators can no longer supply full load. This situation
can be prevented by utilizing the DCDIV resistor divider,
set higher than the minimum adapter voltage where full
power can be achieved.
APPLICATIONS INFORMATION
CALIBRATION MODE BACK-DRIVE CURRENT
PROTECTION
A resistor between CLP and CLN programs the minimum
supply forward current, this feature prevent the LTC4110
from back-driving the supply in calibration mode and
pulling the voltage higher when the system load is low.
The resistor value is given by
R
I
CL
BDT
FR MIN
=
()
where
IBDT = back-drive current limit threshold, 10mV typical
IFR(MIN) = minimum forward current in calibration mode
An RC lter may be required to lter out system load noise
as shown in Figure 11.
BATTERY AND CHARGER CURRENT SENSE
The LTC4110 uses two sense resistors to monitor and
control all charge and calibration currents: RSNS(BAT) and
RSNS(FET).
RSNS(BAT)
RSNS(BAT) is used to monitor the DC current going into
the battery for charge, and the current going out of the
battery for calibration. Before any current programming
can be done, the value of RSNS(BAT) must be determined
rst. Highest accuracy is achieved when full-scale current,
IMAX is set to develop a 100mV drop across the resistor.
Although values greater than 100mV can be used to improve
accuracy, this requires larger sense resistors to handle
the extra heat and lower efciency. IMAX must be set to
Figure 11. Back-Drive Protection
10mV
TO
SYSTEM
LOAD
4110 F11
–
+
VIN
CIN
100nF
10mV
5k
CLP
CLN
CL1
LTC4110
BACK
DRIVE
+
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4110EUHF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4151CS-2#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4151HMS#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4151HDD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4151HDD#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
| LTC4150CMS | 功能描述:IC COUNTER/GAUGE GAS/BATT 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。