- 您現在的位置：買賣IC網 > PDF目錄44996 > LTC4110EUHF#TR (LINEAR TECHNOLOGY CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 PDF資料下載
參數資料
| 型號： | LTC4110EUHF#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| 封裝： | 5 X 7 MM, 0.75 MM HEIGHT, PLASTIC, MO-220WHKD, QFN-38 |
| 文件頁數： | 10/52頁 |
| 文件大?。?/td> | 450K |
| 代理商： | LTC4110EUHF#TR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
LTC4110
18
4110fb
SMBUS WAKE-UP CHARGE STATE
The battery will be charged with a xed “wake-up” current
regardless of previous ChargingCurrent() and Charging-
Voltage() register values during wake-up charging. The cur-
rent is identical to the preconditioning charge current which
is programmed with an external resistor through the IPCC
pin. The wake-up timer has the same period as tTIMEOUT,
typically 175sec (see tTIMEOUT).
The following conditions must be met to allow wake-up
charge of the battery:
The SafetySignal must be RES_COLD, RES_IDEAL, or
RES_UR.
AC must be present. This is qualied by DCDIV > VAC
+ VACH and DCIN above UVLO.
Wake-up charge initiates if a battery does not write
non-zero values to ChargingCurrent() and Chargin-
Voltage() registers when AC power is applied and a
battery is present or when AC is present and a battery
is subsequently connected.
The following conditions will terminate the wake-up charge
state and end charge attempts, unless otherwise noted.
The tTIMEOUT period is reached (see tTIMEOUT) when
the SafetySignal is RES_COLD or RES_UR. The state
machine will go to the SMBus OFF state. The CHG_FLT
bit is not set.
The SafetySignal is registering RES_HOT. The state
machine will go to the SMBus OFF state.
The SafetySignal is registering RES_OR. The state
machine will go to the reset state.
The LTC4110 will leave the wake-up charge state and
go into the SMBus preconditioning charge state if the
ChargingCurrent() AND ChargingVoltage() registers
have been written to non-zero values.
The AC power is no longer present (DCDIV < VAC or
DCIN below UVLO). The state machine will go to the
reset state.
The ALARM_INHIBITED becomes set in the
ChargerStatus() register. The state machine will go to
the SMBus OFF state.
CHARGE_INHIBIT is set in the BBuControl() register.
Charge is stopped, however, the wake-up timer is not
paused. Clearing CHARGE_INHIBIT will enable the
LTC4110 to resume charging.
There is insufcient DCIN voltage to charge the battery
as determined by the internal UVLO. This causes the
state machine to enter the reset state and stop all charge
activity.TheLTC4110willresumewake-upchargingwhen
there is sufcient DCIN voltage to charge the battery.
The CAL_START bit in the BBuControl() register is set.
Charge is stopped and the LTC4110 enters the calibra-
tion state.
Writing a zero value to either the ChargingVoltage() or
ChargingCurrent() register. The state machine will go
to the SMBus OFF state.
RESET_TO_ZERO is set in the BBuControl() register.
Charge is stopped; the SMBus OFF State is entered.
SMBUS PRECONDITIONING CHARGE STATE
During the SMBus preconditioning charge state, the charger
will be operating in the preconditioning charge current
limit. The following conditions must be met in order to
allow SMBus preconditioning charge to start:
The ChargingVoltage() AND ChargingCurrent() registers
must be written to non-zero values. The LTC4110 will
not directly report the status of these registers. The
battery needs only write one pair of ChargingVoltage()
and ChargingCurrent() registers to stay in this state. The
tTIMEOUTtimerisnotoperationalinSMBusprecondition-
ing charge state.
The SafetySignal must be RES_COLD, RES_IDEAL, or
RES_UR.
AC must be present and sufcient. This is qualied by
DCDIV > VAC + VACH and DCIN > UVLO.
The following conditions will affect the SMBus precondi-
tioning charge state as specied below:
The SafetySignal is registering RES_HOT. Charge is
stopped; the SMBus OFF state is entered.
OPERATION
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4110EUHF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC38 |
| LTC4151CS-2#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| LTC4151HMS#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4151HDD#TRPBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
| LTC4151HDD#PBF | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4110EUHF-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Battery Backup System Manager |
| LTC4120IUD#PBF | 制造商:Linear Technology 功能描述:BATTERY CHARGER, 400MA, QFN-16, Battery Type:Li-Ion, Li-Polymer, Input Voltage:4 |
| LTC4150 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage, High-Side Current Sense |
| LTC4150_1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Coulomb Counter/ Battery Gas Gauge |
| LTC4150CMS | 功能描述:IC COUNTER/GAUGE GAS/BATT 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。