參數資料
型號： ISP1161A1
廠商： NXP Semiconductors N.V.
英文描述： Universal Serial Bus single-chip host and device controller
中文描述： 通用串行總線的單芯片主機和設備控制器
文件頁數： 30/127頁
文件大小： 2762K
代理商： ISP1161A1
Philips Semiconductors
ISP1161
Full-speed USB single-chip host and device controller
Product data
Rev. 01 — 3 July 2001
30 of 130
9397 750 08313
Philips Electronics N.V. 2001. All rights reserved.
9.4.3
Operation & C Program Example
Figure 29
shows the block diagram for internal FIFO buffer RAM operations by PIO
mode. ISP1161 provides one register as the access port for each buffer RAM. For the
ITL buffer RAM, the access port is the ITLBufferPort register (40H - Read, C0H -
Write). For the ATL buffer RAM, the access port is the ATLBufferPort register (41H -
Read, C1H - Write). The buffer RAM is an array of bytes (8 bits) while the access port
is a 16-bit register. Therefore, each read/write operation on the port accesses two
consecutive memory locations, incrementing the pointer of the internal buffer RAM by
two.
The lower byte of the access port register corresponds to the data byte at the even
location of the buffer RAM, and the higher byte in the access port register
corresponds to the other data byte at the odd location of the buffer RAM. Regardless
of the number of data bytes to be transferred, the command code must be issued
merely once, and it will be followed by a number of accesses of the data port (see
Section 8.4
).
When the pointer of the buffer RAM reaches the value of the HcTransferCounter
register, an internal EOT signal will be generated to set bit 2, AllEOTInterrupt, of the
Hc
μ
Pinterrupt register and update the HcBufferStatus register, to indicate that the
whole data transfer has been completed.
For ITL buffer RAM, every start of frame (SOF) signal (1 ms) will cause toggling
between ITL0 and ITL1 but this depends on the buffer status. If both ITL0BufferFull
and ITL1BufferFull of the HcBufferStatus register are already logic 1, meaning that
both ITL0 and ITL1 buffer RAMs are full, the toggling will not happen. In this case, the
microprocessor will always have access to ITL1.
Fig 28. PTD data with DWORD alignment in buffer RAM.
MGT953
payload data
(14 bytes)
PTD
(8 bytes)
PTD
(8 bytes)
00H
top
08H
15H
18H
20H
payload data
RAM buffer
相關PDF資料
PDF描述
ISP1161A1BD Universal Serial Bus single-chip host and device controller
ISP1161A1BM Universal Serial Bus single-chip host and device controller
ISP1161BD Full-speed Universal Serial Bus single-chip host and device controller
ISP1161BM Full-speed Universal Serial Bus single-chip host and device controller
ISP1181ABS INDUCTOR 1.0NH +-.3NH FIXED SMD
相關代理商/技術參數
參數描述
ISP1161A1BD 功能描述:IC USB HOST/DEVICE CTRLR 64-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
ISP1161A1BD,118 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1161A1BD,151 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1161A1BD,157 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1161A1BDFA 功能描述:IC USB HOST CONTROLLER 64LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*