- 您現在的位置：買賣IC網 > PDF目錄1924 > IDT82P5088BBG (IDT, Integrated Device Technology Inc)IC LIU T1/E1/J1 OCTAL 256PBGA PDF資料下載
參數資料
| 型號： | IDT82P5088BBG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 10/81頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 OCTAL 256PBGA |
| 標準包裝： | 90 |
| 功能： | 線路接口單元（LIU） |
| 接口： | E1，J1，T1 |
| 電路數： | 8 |
| 電源電壓： | 1.8V, 3.3V |
| 功率（瓦特）： | 2.57W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 256-BGA |
| 供應商設備封裝： | 256-PBGA（17x17） |
| 包裝： | 托盤 |
| 包括： | 集成式時鐘適配器 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
IDT82P5088
UNIVERSAL OCTAL T1/E1/J1 LIU WITH INTEGRATED CLOCK ADAPTER
FUNCTIONAL DESCRIPTION
18
February 5, 2009
Figure-5 DSX-1 Waveform Template
Figure-6 T1 Pulse Template Test Circuit
For J1 applications, the PULS[3:0] (TCF1, 23H...) should be set to
‘0111’. Table-14 lists these values.
3.2.3.2 LBO (Line Build Out)
To prevent the cross-talk at the far end, the output of TTIP/TRING could
be attenuated before transmission for long haul applications. The FCC Part
68 Regulations specifies four grades of attenuation with a step of 7.5 dB.
Three LBOs are used to implement the pulse attenuation. The PULS[3:0]
bits (TCF1, 23H...) are used to select the attenuation grade. Both Table-14
and Table-16 list these values.
3.2.3.3 User-Programmable Arbitrary Waveform
When the PULS[3:0] bits are set to ‘11xx’, user-programmable arbitrary
waveform generator mode can be used in the corresponding channel. This
allows the transmitter performance to be tuned for a wide variety of line con-
dition or special application.
Each pulse shape can extend up to 4 UIs (Unit Interval), addressed by
UI[1:0] bits (TCF3, 25H...) and each UI is divided into 16 sub-phases,
addressed by the SAMP[3:0] bits (TCF3, 25H...). The pulse amplitude of
each phase is represented by a binary byte, within the range from +63 to -
63, stored in WDAT[6:0] bits (TCF4, 26H...) in signed magnitude form. The
most positive number +63 (D) represents the maximum positive amplitude
of the transmit pulse while the mostnegative number -63 (D) represents the
maximum negative amplitude of the transmit pulse. Therefore, up to 64
bytes are used. For each channel, a 64 bytes RAM is available.
There are twelve standard templates which are stored in a local ROM.
User can select one of them as reference and make some changes to get
the desired waveform.
User can change the wave shape and the amplitude to get the desired
pulse shape. In order to do this, firstly, users can choose a set of waveform
value from the following twelve tables, which is the most similar to the
desired pulse shape. Table-2, Table-3, Table-4, Table-5, Table-6, Table-7,
data and scaling data of each of the twelve templates. Then modify the cor-
responding sample data to get the desired transmit pulse shape.
Secondly, through the value of SCAL[5:0] bits increased or decreased
by 1, the pulse amplitude can be scaled up or down at the percentage ratio
against the standard pulse amplitude if needed. For different pulse shapes,
the value of SCAL[5:0] bits and the scaling percentage ratio are different.
The following twelve tables list these values.
Do the followings step by step, the desired waveform can be pro-
grammed, based on the selected waveform template:
(1).Select the UI by UI[1:0] bits (TCF3, 25H...)
(2).Specify the sample address in the selected UI by SAMP [3:0] bits
(TCF3, 25H...)
(3).Write sample data to WDAT[6:0] bits (TCF4, 26H...). It contains the
data to be stored in the RAM, addressed by the selected UI and the
corresponding sample address.
(4).SettheRWbit(TCF3,25H...)to‘0’toimplementwritingdatatoRAM,
or to ‘1’ to implement read data from RAM
(5).Implement the Read from RAM/Write to RAM by setting the DONE
bit (TCF3, 25H...)
Repeat the above steps until all the sample data are written to or read
from the internal RAM.
(6).Write the scaling data to SCAL[5:0] bits (TCF2, 24H...) to scale the
amplitude of the waveform based on the selected standard pulse
amplitude
WhenmorethanoneUIisusedtocomposethepulsetemplate,theover-
lap of two consecutive pulses could make the pulse amplitude overflow
(exceed the maximum limitation) if the pulse amplitude is not set properly.
This overflow is captured by DAC_IS bit (INTS1, 3BH...), and, if enabled
by the DAC_IE bit (INTENC1, 34H...), an interrupt will be generated.
The following tables give all the sample data based on the preset pulse
templates and LBOs in detail for reference. For preset pulse templates and
LBOs, scaling up/down against the pulse amplitude is not supported.
1.Table-2 Transmit Waveform Value For E1 75
2.Table-3 Transmit Waveform Value For E1 120
3.Table-4 Transmit Waveform Value For T1 0~133 ft
4.Table-5 Transmit Waveform Value For T1 133~266 ft
5.Table-6 Transmit Waveform Value For T1 266~399 ft
6.Table-7 Transmit Waveform Value For T1 399~533 ft
7.Table-8 Transmit Waveform Value For T1 533~655 ft
8.Table-9 Transmit Waveform Value For J1 0~655 ft
9.Table-10 Transmit Waveform Value For DS1 0 dB LBO
10.Table-11 Transmit Waveform Value For DS1 -7.5 dB LBO
11.Table-12 Transmit Waveform Value For DS1 -15.0 dB LBO
-0.6
-0.4
-0.2
0
0.2
0.4
0.6
0.8
1
1.2
0
250
500
750
1000
1250
Time (ns)
Normalized
A
m
plitude
IDT82P5088
TTIPn
TRINGn
Cable
RLOAD VOUT
Note: RLOAD = 100
± 5%
相關PDF資料 |
PDF描述 |
|---|---|
| IDT82V2041EPPG | IC LIU T1/J1/E1 1CH 44-TQFP |
| IDT82V2042EPFG | IC LIU T1/J1/E1 2CH SHORT 80TQFP |
| IDT82V2044EPFG | IC LIU T1/E1 QUAD SHORT 128-TQFP |
| IDT82V2048DAG | IC LIU T1/E1 8CH SHORT 144-TQFP |
| IDT82V2048EDR | IC LIU T1/E1 8CH SHORT 208-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82P5088BBG8 | 制造商:Integrated Device Technology Inc 功能描述:IC LIU T1/E1/J1 OCTAL 256PBGA |
| IDT82V1054A | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:QUAD PROGRAMMABLE PCM CODEC WITH MPI INTERFACE |
| IDT82V1054APF | 功能描述:IC PCM CODEC 4CH MPI 3.3V 64TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| IDT82V1054APF8 | 功能描述:IC PCM CODEC 4CH MPI 3.3V 64TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| IDT82V1054APFG | 功能描述:IC PCM CODEC 4CH MPI 3.3V 64TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。