- 您現在的位置：買賣IC網 > PDF目錄97907 > ELANSC410 Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: 0°C to 70°C; Package: 16-QFN PDF資料下載
參數資料
| 型號： | ELANSC410 |
| 英文描述： | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: 0°C to 70°C; Package: 16-QFN |
| 中文描述： | ElanSC410 - ElanSC410框圖 |
| 文件頁數： | 49/119頁 |
| 文件大小： | 1167K |
| 代理商： | ELANSC410 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁當前第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁
lanSC310 Microcontroller Data Sheet
35
PREL IMINARY
are asserted Low immediately after reset, and the
PMC3 signal is asserted High immediately after reset.
Each of the PMC pins can then be programmed to be
High or Low for each of the lanSC310 microcontroller
power management modes.
SUS/RES
Suspend/Resume Operation (Input; Rising Edge)
When the lanSC310 microcontroller is in High Speed
PLL, Low Speed PLL, or Doze mode, a positive edge
on this pin causes the internal logic to step down
through the Power Management modes (one per re-
fresh cycle) until Sleep mode is entered. If in Sleep,
Suspend, or Off mode, a positive edge on this pin
causes the lanSC310 microcontroller to enter the
High Speed PLL mode.
MISCELLANEOUS INTERFACE
LF1, LF2, LF3, LF4 (Analog inputs)
Loop Filters
These pins are used to connect external components
that make up the loop filters for the internal PLLs. For
more information, see “Loop Filters” on page 86.
X1OUT [BAUD-OUT]
14-MHz/UART Output
This can be programmed to be either the 14.336-MHz
clock or the serial baud rate clock for serial infrared de-
vices. The 14.336-MHz output can be used by external
video controllers. As BAUD_OUT, it is 16 x the bit data
rate of the serial port and is used by serial infrared
devices.
X14OUT
14-MHz Output
The Parallel Port AFDT output can be programmed to
become X14OUT, a 14.336-MHz clock.
X32IN, X32OUT
32.768-kHz Crystal Interface
These pins are used for the 32.768-kHz crystal. This is
the main clock source for the lanSC310 microcontrol-
ler and is used to drive the internal Phase-Locked
Loops that generate all other clock frequencies needed
in the system. For more information, see “Crystal Spec-
LOCAL BUS INTERFACE
The following list of pins is specific to local bus function-
ality. In Local Bus mode, additional ISA pins are also
available. These pins are described in the next section
“Maximum ISA Bus Interface” because these pins are
available in both Local Bus and Maximum ISA Bus
modes.
For more information, see “Maximum ISA Interface ver-
ADS
Local Bus Address Strobe (Output; Active Low)
Local Bus Address Strobe is an active Low address
strobe signal for 386 local bus devices.
BHE
Local Bus Byte High Enable (Output; Active Low)
This signal indicates to the local bus devices that data
is being transferred on the high byte of the data bus.
BLE
Local Bus Byte Low Enable (Output; Active Low)
This signal indicates to the local bus devices that data
is being transferred on the low byte of the data bus.
CPUCLK (PULLUP)
CPU 2X Clock (Output)
This is the timing reference for the local bus device.
The high-speed PLL can be programmed to provide
one of the clock frequencies shown on page 44.
CPURDY
386 CPU Ready Signal (Output; Active Low)
This signal shows the current state of the 386 core
CPU’s CPURDY signal.
CPURST (RSVD)
CPU Reset (Output; Active High)
This signal is used to force the local bus device to an
initial condition. It is also used to allow the local bus de-
vice to synchronize to the CPUCLK. This signal is
taken directly from the internal CPU reset.
D/C
Local Bus Data/Control (Output; Active Low)
This signal indicates to the local bus devices that the
current cycle is either a Data cycle or a Control cycle.
A Low on this signal indicates that the current cycle is
a Control cycle.
LDEV (RSVD)
Local Bus Device Select (Input; Active Low)
This signal is used by the local bus devices to signal
that they will respond to the current cycle. If LDEV is
not driven active by the time required in Table 51 on
page 98, then the cycle defaults to an ISA bus cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| ELH0032G | Fast Operational Amplifier |
| ELH0033G | Fast Buffer Amplifier |
| ELH0101CK | Dual Regulator-Standard Buck PWM and Linear Power Controller; Temperature Range: 0°C to 70°C; Package: 8-SOIC T&R |
| ELH0101ACK | Single Synchronous Buck Pulse-Width Modulation (PWM) Controller; Temperature Range: -40°C to 85°C; Package: 16-QFN |
| ELH0101 | Power Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELANSC410-100AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC ROMLess 3.3V 292-Pin BGA |
| ELANSC410-100ACAD | 制造商:Advanced Micro Devices 功能描述: |
| ELANSC410-100AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-33AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC 3.3V 292-Pin BGA |
| ELANSC410-33AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。