參數資料
型號： CC113LRTKT
廠商： TEXAS INSTRUMENTS INC
元件分類： 無繩電話/電話
英文描述： TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, PQCC20
封裝： 4 X 4 MM, GREEN, PLASTIC, VQFN-20
文件頁數： 37/75頁
文件大?。?/td> 1454K
代理商： CC113LRTKT
CC113L
SWRS108A
Page 42 of 68
GDOx_CFG[5:0]
Description
0 (0x00)
Associated to the RX FIFO: Asserts when RX FIFO is filled at or above the RX FIFO threshold. De-
asserts when RX FIFO is drained below the same threshold.
1 (0x01)
Associated to the RX FIFO: Asserts when RX FIFO is filled at or above the RX FIFO threshold or the
end of packet is reached. De-asserts when the RX FIFO is empty.
2 (0x02) - 3 (0x03)
Reserved - used for test.
4 (0x04)
Asserts when the RX FIFO has overflowed. De-asserts when the FIFO has been flushed.
5 (0x05)
Reserved - used for test.
6 (0x06)
Asserts when sync word has been received, and de-asserts at the end of the packet. The pin will
also de-assert when a packet is discarded due to address or maximum length filtering or when the
radio enters RXFIFO_OVERFLOW state.
7 (0x07)
Asserts when a packet has been received with CRC OK. De-asserts when the first byte is read from
the RX FIFO.
8 (0x08) - 9 (0x09)
Reserved - used for test.
10 (0x0A)
Lock detector output. The PLL is in lock if the lock detector output has a positive transition or is
constantly logic high. To check for PLL lock the lock detector output should be used as an interrupt
for the MCU.
11 (0x0B)
Serial Clock. Synchronous to the data in synchronous serial mode.
Data is set up on the falling edge by CC113L when GDOx_INV=0.
12 (0x0C)
Serial Synchronous Data Output. Used for synchronous serial mode.
13 (0x0D)
Serial Data Output. Used for asynchronous serial mode.
14 (0x0E)
Carrier sense. High if RSSI level is above threshold. Cleared when entering IDLE mode.
15 (0x0F)
CRC_OK. The last CRC comparison matched. Cleared when entering/restarting RX mode.
16 (0x10) - 27 (0x1B)
Reserved - used for test.
28 (0x1C)
LNA_PD. Note: LNA_PD will have the same signal level in SLEEP and RX states. To control an
external LNA in applications where the SLEEP state is used it is recommended to use
29 (0x1D)
– 38 (0x26)
Reserved - used for test.
39 (0x27)
CLK_32k.
40 (0x28)
Reserved - used for test.
41 (0x29)
CHIP_RDYn.
42 (0x2A)
Reserved - used for test.
43 (0x2B)
XOSC_STABLE.
44 (0x2C)
– 45 (0x2D)
Reserved - used for test.
46 (0x2E)
High impedance (3-state).
47 (0x2F)
HW to 0 (HW1 achieved by setting GDOx_INV=1). Can be used to control an external LNA
48 (0x30)
CLK_XOSC/1
Note: There are 3 GDO pins, but only one CLK_XOSC/n can be selected as an
output at any time. If CLK_XOSC/n is to be monitored on one of the GDO pins,
the other two GDO pins must be configured to values less than 0x30. The
GDO0 default value is CLK_XOSC/192.
To optimize RF performance, these signals should not be used while the radio is
in RX mode.
49 (0x31)
CLK_XOSC/1.5
50 (0x32)
CLK_XOSC/2
51 (0x33)
CLK_XOSC/3
52 (0x34)
CLK_XOSC/4
53 (0x35)
CLK_XOSC/6
54 (0x36)
CLK_XOSC/8
55 (0x37)
CLK_XOSC/12
56 (0x38)
CLK_XOSC/16
57 (0x39)
CLK_XOSC/24
58 (0x3A)
CLK_XOSC/32
59 (0x3B)
CLK_XOSC/48
60 (0x3C)
CLK_XOSC/64
61 (0x3D)
CLK_XOSC/96
62 (0x3E)
CLK_XOSC/128
63 (0x3F)
CLK_XOSC/192
Table 29: GDOx Signal Selection (x = 0, 1, or 2)
相關PDF資料
PDF描述
CC154Z-A6BP45-FREQTSB-OUT27 VCXO, CLOCK, 8 MHz - 36 MHz, HCMOS OUTPUT
CC1812C513R-10 CHOKE CAN-BUS 51.0UH 200MA
CC2824B475R-10 CHOKE CAN-BUS 4700.0UH 400MA
CC2824D225R-10 CHOKE CAN-BUS 2200.0UH 500MA
CC2824E105R-10 CHOKE CAN-BUS 1000.0UH 700MA
相關代理商/技術參數
參數描述
CC113U015R3C3PH 制造商:Mallory 功能描述:CGA015X311B
CC1140M3M 制造商:SHIELD 制造商全稱:SHIELD s.r.l. 功能描述:For electrovalves, style A, 3p+G, female, with cable
CC1140M8M 制造商:SHIELD 制造商全稱:SHIELD s.r.l. 功能描述:For electrovalves, style A, 3p+G, female, with cable
CC-115 制造商:B&K Precision Corporation 功能描述:
CC1150 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CC1100 Single Chip Low Cost Low Power RF-Transceiver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*