參數資料
型號： ADUC824BSZ-REEL
廠商： Analog Devices Inc
文件頁數： 43/68頁
文件大?。?/td> 0K
描述： IC MCU 8K FLASH ADC/DAC 52MQFP
標準包裝： 800
系列： MicroConverter® ADuC8xx
核心處理器： 8052
芯體尺寸： 8-位
速度： 12.58MHz
連通性： EBI/EMI，I²C，SPI，UART/USART
外圍設備： POR，PSM，溫度傳感器，WDT
輸入/輸出數： 34
程序存儲器容量： 8KB（8K x 8）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 640 x 8
RAM 容量： 256 x 8
電壓 - 電源 (Vcc/Vdd)： 2.7 V ~ 5.25 V
數據轉換器： A/D 3x16b，4x24b; D/A 1x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 52-QFP
包裝： 帶卷 (TR)
REV. B
ADuC824
–48–
SERIAL PERIPHERAL INTERFACE
The ADuC824 integrates a complete hardware Serial Peripheral
Interface (SPI) interface on-chip. SPI is an industry standard syn-
chronous serial interface that allows eight bits of data to be
synchronously transmitted and received simultaneously, i.e., full
duplex. It should be noted that the SPI physical interface is shared
with the I
2C interface and therefore the user can only enable one
or the other interface at any given time (see SPE in SPICON
below). The system can be configured for Master or Slave operation
and typically consists of four pins, namely:
MISO (Master In, Slave Out Data I/O Pin), Pin#14
The MISO (master in slave out) pin is configured as an input line
in master mode and an output line in slave mode. The MISO
line on the master (data in) should be connected to the MISO
line in the slave device (data out). The data is transferred as
byte wide (8-bit) serial data, MSB first.
MOSI (Master Out, Slave In Pin), Pin#27
The MOSI (master out slave in) pin is configured as an output line
in master mode and an input line in slave mode. The MOSI
line on the master (data out) should be connected to the MOSI
line in the slave device (data in). The data is transferred as byte
wide (8-bit) serial data, MSB first.
SCLOCK (Serial Clock I/O Pin), Pin#26
The master clock (SCLOCK) is used to synchronize the data
being transmitted and received through the MOSI and MISO data
lines. A single data bit is transmitted and received in each SCLOCK
period. Therefore, a byte is transmitted/received after eight
SCLOCK periods. The SCLOCK pin is configured as an output
in master mode and as an input in slave mode. In master mode
the bit-rate, polarity and phase of the clock are controlled by
the CPOL, CPHA, SPR0 and SPR1 bits in the SPICON SFR
(see Table XIX). In slave mode the SPICON register will have
to be configured with the phase and polarity (CPHA and CPOL)
of the expected input clock. In both master and slave mode
the data is transmitted on one edge of the SCLOCK signal and
sampled on the other. It is important therefore that the CPHA
and CPOL are configured the same for the master and slave devices.
SS (Slave Select Input Pin), Pin#13
The Slave Select (
SS) input pin is only used when the ADuC824
is configured in slave mode to enable the SPI peripheral. This line
is active low. Data is only received or transmitted in slave mode
when the
SS pin is low, allowing the ADuC824 to be used in single
master, multislave SPI configurations. If CPHA = 1 then the
SS
input may be permanently pulled low. With CPHA = 0 then the
SS input must be driven low before the first bit in a byte wide
transmission or reception and return high again after the last bit
in that byte wide transmission or reception. In SPI Slave Mode,
the logic level on the external
SS pin (Pin# 13), can be read
via the SPR0 bit in the SPICON SFR.
The following SFR registers are used to control the SPI interface.
SPICON
SPI Control Register
SFR Address
F8H
Power-On Default Value
04H
Bit Addressable
Yes
I
P
S
IL
O
C
WE
P
SM
I
P
SL
O
P
CA
H
P
C1
R
P
S0
R
P
S
Table XIX. SPICON SFR Bit Designations
Bit
Name
Description
7
ISPI
SPI Interrupt Bit
Set by MicroConverter at the end of each SPI transfer.
Cleared directly by user code or indirectly by reading the SPIDAT SFR.
6
WCOL
Write Collision Error Bit
Set by MicroConverter if SPIDAT is written to while an SPI transfer is in progress.
Cleared by user code.
5
SPE
SPI Interface Enable Bit
Set by user to enable the SPI interface.
Cleared by user to enable the I
2C interface.
4
SPIM
SPI Master/Slave Mode Select Bit
Set by user to enable Master Mode operation (SCLOCK is an output).
Cleared by user to enable Slave Mode operation (SCLOCK is an input).
3
CPOL
*
Clock Polarity Select Bit
Set by user if SCLOCK idles high.
Cleared by user if SCLOCK idles low.
2
CPHA
*
Clock Phase Select Bit
Set by user if leading SCLOCK edge is to transmit data.
Cleared by user if trailing SCLOCK edge is to transmit data.
1
SPR1
SPI Bit-Rate Select Bits
0
SPR0
These bits select the SCLOCK rate (bit-rate) in Master Mode as follows:
SPR1
SPR0
Selected Bit Rate
SPR1
SPR0
Selected Bit Rate
00fCORE/2
10fCORE/8
01fCORE/4
11fCORE/16
In SPI Slave Mode, i.e., SPIM = 0, the logic level on the external
SS pin (Pin# 13), can be read via the SPR0 bit.
*Bits should contain the same values for master and slave devices.
相關PDF資料
PDF描述
ADUC831BCPZ IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC832BSZ-REEL IC MCU 62K FLASH ADC/DAC 52MQFP
ADUC834BCPZ-REEL IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC836BCPZ IC MCU 62K FLASH ADC/DAC 56LFCSP
ADUC843BSZ62-5 IC ADC 12BIT W/FLASH MCU 52-MQFP
相關代理商/技術參數
參數描述
ADUC831 制造商:AD 制造商全稱:Analog Devices 功能描述:MicroConverter, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU
ADUC831BCP 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADUC831BCP-REEL 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 56-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED 8-BIT MCU I.C. - Tape and Reel
ADUC831BCPZ 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
ADUC831BCPZ-REEL 功能描述:IC MCU 62K FLASH ADC/DAC 56LFCSP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA，UART/USART 外圍設備:欠壓檢測/復位，LED，POR，PWM，WDT 輸入/輸出數:16 程序存儲器容量:4KB（4K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*