- 您現在的位置：買賣IC網 > PDF目錄373972 > AD9991 (Analog Devices, Inc.) 10-Bit CCD Signal Processor with Precision Timing Generator PDF資料下載
參數資料
| 型號： | AD9991 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 10-Bit CCD Signal Processor with Precision Timing Generator |
| 中文描述： | 10位CCD信號處理器與精密時序發生器 |
| 文件頁數： | 34/60頁 |
| 文件大?。?/td> | 826K |
| 代理商： | AD9991 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
AD9991
–34–
SYNC during Master Mode Operation
The SYNC input may be used any time during operation to
resync the AD9991 counters with external timing, as shown in
Figure 36. The operation of the digital outputs may be suspended
during the SYNC operation by setting the SYNCSUSPEND
register (addr 0x14) to a 1.
Power-Up and Synchronization in Slave Mode
The power-up procedure for Slave mode operation is the same
as the procedure described for Master mode operation, with two
exceptions:
Eliminate Step 9. Do not write the part into Master mode.
No SYNC pulse is required in Slave mode. Substitute Step 12
with starting the external VD and HD signals. This will syn-
chronize the part, allow the Bank 1 register updates, and start
the timing operation.
When the AD9991 is used in Slave mode, the VD and HD inputs
are used to synchronize the internal counters. Following a falling
edge of VD, there will be a latency of 17 master clock cycles (CLI)
after the falling edge of HD until the internal H-counter will be
reset. The reset operation is shown in Figure 37.
STANDBY MODE OPERATION
The AD9991 contains three different standby modes
to optimize the overall power dissipation in a particular
application. Bits [1:0] of the OPRMODE register control
the power-down state of the device:
OPRMODE [1:0] = 00 = Normal Operation (Full Power)
OPRMODE[1:0] = 01 = Standby 1 Mode
OPRMODE[1:0] = 10 = Standby 2 Mode
OPRMODE[1:0] = 11 = Standby 3 Mode (Lowest Overall Power)
Table XIV summarizes the operation of each power-
down mode. Note that the OUT_CONTROL register
takes priority over the Standby 1 and Standby 2 modes in
determining the digital outpu t states, but Standby 3 mode
takes priority over OUT_CONTROL. Standby 3 has the
lowest power consumption, and even shuts down the crystal
oscillator circuit between CLI and CLO. Thus, if CLI and
CLO are being used with a crystal to generate the master
clock, this circuit will be powered down and there will be no
clock signal. When returning from Standby 3 mode to normal
operation, the timing core must be reset at least 500 μs after the
OPRMODE register is written to. This will allow sufficient
time for the crystal circuit to settle.
VD
HD
NOTES
1. SYNC RISING EDGE RESETS VD/HD AND COUNTERS TO ZERO.
2. SYNC POLARITY IS PROGRAMMABLE USING SYNCPOL REGISTER (ADDR 0x13).
3. DURING SYNC LOW, ALL INTERNAL COUNTERS ARE RESET AND VD/HD CAN BE SUSPENDED USING THE SYNCSUSPEND REGISTER (ADDR 0x14).
4. IF SYNCSUSPEND = 1, VERTICAL CLOCKS, H1–H2, AND RG ARE HELD AT THEIR DEFAULT POLARITIES.
5. IF SYNCSUSPEND = 0, ALL CLOCK OUTPUTS CONTINUE TO OPERATE NORMALLY UNTIL SYNC RESET EDGE.
SUSPEND
SYNC
H124, RG, V1–V4,
VSG, SUBCK
Figure 36. SYNC Timing to Synchronize AD9991 with External Timing
0
1
2
3
4
5
6
7
8
H-COUNTER
RESET
VD
NOTES
INTERNAL H-COUNTER IS RESET 17 CLI CYCLES AFTER THE HD FALLING EDGE (WHEN USING VDHDPOL = 0).
TYPICAL TIMING RELATIONSHIP: CLI RISING EDGE IS COINCIDENT WITH HD FALLING EDGE.
HD
CLI
X
X
X
X
X
X
X
X
X
H-COUNTER
(PIXEL COUNTER)
X
X
X
X
X
X
X
X
X
X
9
Figure 37. External VD/HD and Internal H-Counter Synchronization, Slave Mode
REV. 0
相關PDF資料 |
PDF描述 |
|---|---|
| AD9992 | 12-Bit CCD Signal Processor with Precision Timing Generator |
| AD9992BBCZ | 12-Bit CCD Signal Processor with Precision Timing Generator |
| AD9992BBCZRL | 12-Bit CCD Signal Processor with Precision Timing Generator |
| AD9995KCP | 12-Bit CCD Signal Processor with Precision Timing ⑩ Generator |
| AD9995KCPRL | 12-Bit CCD Signal Processor with Precision Timing ⑩ Generator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9991KCP | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AD9991KCPRL | 制造商:Analog Devices 功能描述:AFE Video 1ADC 10-Bit 3V 56-Pin LFCSP EP T/R |
| AD9991KCPZ | 功能描述:IC CCD SIGNAL PROCESSOR 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9991KCPZRL | 功能描述:IC CCD SIGNAL PROCESSOR 56-LFCSP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| AD9992 | 制造商:AD 制造商全稱:Analog Devices 功能描述:12-Bit CCD Signal Processor with Precision Timing Generator |
發布緊急采購，3分鐘左右您將得到回復。