- 您現在的位置：買賣IC網 > PDF目錄17065 > AD9788-DPG2-EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9788 PDF資料下載
參數資料
| 型號： | AD9788-DPG2-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 25/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD9788 |
| 設計資源： | Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141) |
| 標準包裝： | 1 |
| 系列： | * |
| DAC 的數量： | 2 |
| 位數： | 16 |
| 采樣率（每秒）： | 800M |
| 數據接口： | 串行 |
| 設置時間： | 22ms |
| DAC 型： | 電流 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | * |
| 已用 IC / 零件： | AD9788 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
AD9785/AD9787/AD9788
Rev. A | Page 31 of 64
The interrupt control register comprises two bytes located at Address 0x09. Bits [11:10] and Bits [7:3] are read-only bits that indicate the
current status of a specific event that may cause an interrupt request (IRQ pin active low). These bits are controlled via the digital logic
and are read only via the serial port. Bits [1:0] are the IRQ mask (or enable) bits, which are writable by the user and can also be read back.
Table 19. Interrupt Control Register
Address
Bit
Name
Description
0x09
[15:13]
Reserved
Reserved for future use.
[12]
Clear lock indicator
Writing a 1 to this bit clears the sync lock lost status bit. This bit does not automatically
reset itself to 0 when the reset is complete.
[11]
Sync lock lost status
When high, this bit indicates that the device has lost synchronization. This bit is latched
and does not reset automatically after the device regains synchronization. To reset this
bit to 0, a 1 must be written to the clear lock indicator bit.
[10]
Sync lock status
When this bit is low, the device is not synchronized. When this bit is high, the device is
synchronized.
[9:8]
Reserved
Reserved for future use.
[7]
Data timing error IRQ
0: Default. No setup or hold time error has been detected via the input data port
setup/hold error checking logic.
1: A setup or hold time error has been detected via the input data port setup/hold error
checking logic.
[6]
Sync timing error IRQ
0: Default. No setup or hold time error has been detected via the multichip
synchronization receive pulse setup/hold error checking logic.
1: A setup or hold time error has been detected via the multichip synchronization
receive pulse setup/hold error checking logic.
[5]
Data timing error type
0: Default. A hold error has been detected via the input data port setup/hold error
checking logic. This bit is valid only if the data timing error IRQ bit (Bit 7) is set.
1: A setup error has been detected via the input data port setup/hold error checking
logic. This bit is valid only if the data timing error IRQ bit (Bit 7) bit is set.
[4]
Sync timing error type
0: Default. A hold error has been detected via the multichip synchronization receive
pulse setup/hold error checking logic. This bit is valid only if the sync timing error IRQ
bit (Bit 6) is set.
1: A setup error has been detected via the multichip synchronization receive pulse
setup/hold error checking logic. This bit is valid only if the sync timing error IRQ bit
(Bit 6) is set.
[3]
PLL lock indicator
0: Default. The PLL clock multiplier is not locked to the input reference clock.
1: The PLL clock multiplier is locked to the input reference clock.
[2]
Reserved
Reserved for future use.
[1]
Data port IRQ enable
0: Default. The data IRQ bit (and the IRQ pin) are not enabled (masked) for any errors
that may be detected via the input data port setup/hold error checking logic.
1: The data IRQ bit (and the IRQ pin) are enabled and go active if a setup or hold error is
detected via the input data port setup/hold error checking logic.
[0]
Sync port IRQ enable
0: Default. The sync IRQ bit (and the IRQ pin) are not enabled (masked) for any errors
that may be detected via the multichip synchronization receive pulse setup/hold error
checking logic.
1: The sync IRQ bit (and the IRQ pin) are enabled and go active if a setup or hold error
is detected via the multichip synchronization receive pulse setup/hold error checking
logic.
相關PDF資料 |
PDF描述 |
|---|---|
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
| EMA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| EVAL-AD5392EBZ | BOARD EVAL FOR AD5392 |
| 380LX682M025H022 | CAP ALUM 6800UF 25V 20% SNAP |
| DC941A | BOARD DELTA SIGMA ADC LTC2482 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9788-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9788 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9788MOD-EBZ | 制造商:Analog Devices 功能描述:DUAL 12-/14-/16-BIT 800 MSPS DAC WITH LOW POWER 32-BIT COMPLEX NCO 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk |
| AD9789BBC | 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| AD9789BBCRL | 制造商:Analog Devices 功能描述:QAM Encoder/Interpolator/Upconverter 164-Pin CSP-BGA T/R 制造商:Analog Devices 功能描述:QAM ENCODER/INTERPOLATOR/UPCNVRTR 164CSPBGA - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 14BIT 2.4GSPS 4CH 164BGA 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14 Bit 2.5 GSPS D-A Converter 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14B 2400MSPS RF w/ 4CH Signal Process 制造商:Analog Devices 功能描述:CONVERTER - DAC |
| AD9789BBCZ | 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。