- 您現在的位置：買賣IC網 > PDF目錄17065 > AD9788-DPG2-EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9788 PDF資料下載
參數資料
| 型號： | AD9788-DPG2-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 21/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD9788 |
| 設計資源： | Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141) |
| 標準包裝： | 1 |
| 系列： | * |
| DAC 的數量： | 2 |
| 位數： | 16 |
| 采樣率（每秒）： | 800M |
| 數據接口： | 串行 |
| 設置時間： | 22ms |
| DAC 型： | 電流 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | * |
| 已用 IC / 零件： | AD9788 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
AD9785/AD9787/AD9788
Rev. A | Page 28 of 64
The multichip synchronization register (MSCR) comprises four bytes located at Address 0x03.
Table 13. Multichip Synchronization Register (MSCR)
Address
Bit
Name
Description
0x03
[31:27]
Correlate Threshold
[4:0]
Sets the threshold for determining if the received synchronization data can be demodulated
accurately. A smaller threshold value makes the demodulator more noise immune; however,
the system becomes more susceptible to false locks (or demodulation errors).
[26]
SYNC_I enable
0: Default. The synchronization receive logic is disabled.
1: The synchronization receive logic is enabled.
[25]
SYNC_O enable
0: Default. The output synchronization pulse generation logic is disabled.
1: The output synchronization pulse generation logic is enabled.
[24]
Set low
This bit should always be set low.
[23:19]
SYNC_I Delay [4:0]
This value programs the value of the delay line of the SYNC_I signal. The delay line resolution
is 80 ps per step.
00000: nominal delay
00001: adds 80 ps delay to SYNC_I
00010: adds 160 ps delay to SYNC_I
…
11111: adds 2480 ps delay to SYNC_I
[18]
Sync error check mode
Specifies the synchronization pulse error check mode.
0: Manual error check
1: Automatic continuous error check
[17]
Set low
This bit should always be set low.
[16]
DATACLK input
0: Default. Slave mode is disabled.
1: Slave mode is enabled. Pin 37 functions as an input for the DATACLK signal, called DCI
(DATACLK input) in this mode. Depending on the state of Bit 1 in the DSCR register (Address
0x02), the sampling edge (where the data is latched into the AD9785/AD9787/AD9788) can
be programmed to be aligned with either the rising or falling edge of DCI. This mode can
only be used with 4× or 8× interpolation.
[15:11]
SYNC_O Delay [4:0]
This value programs the value of the delay line of the SYNC_O signal. The delay of SYNC_O is
relative to REFCLK. The delay line resolution is 80 ps per step.
00000: nominal delay
00001: adds 80 ps delay to SYNC_O
00010: adds 160 ps delay to SYNC_O
…
11111: adds 2480 ps delay to SYNC_O
[10]
Set high
This bit should always be set high.
[9]
SYNC_O polarity
0: Default. SYNC_O changes state on the rising edge of DACCLK.
1: SYNC_O is generated on the falling edge of DACCLK.
[8]
Sync loopback enable
0: Default. The AD9785/AD9787/AD9788 are not operating in internal loopback mode.
1: If the SYNC_O enable and Sync loopback enable bits are set, the AD9785/AD9787/AD9788
are operating in a mode in which the internal synchronization pulse of the device is used at
the multichip receiver logic and the SYNC_I+ and SYNC_I input pins are ignored. For proper
operation of the loopback synchronization mode, the synchronization driver enable and
sync enable bits must be set.
[7:4]
Clock State [3:0]
This value determines the state of the internal clock generation state machine upon
synchronization.
[3:0]
Sync Timing Margin
[3:0]
These bits are the synchronization window delay word. These bits are don’t care if the
synchronization driver enable bit is cleared.
相關PDF資料 |
PDF描述 |
|---|---|
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
| EMA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| EVAL-AD5392EBZ | BOARD EVAL FOR AD5392 |
| 380LX682M025H022 | CAP ALUM 6800UF 25V 20% SNAP |
| DC941A | BOARD DELTA SIGMA ADC LTC2482 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9788-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9788 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9788MOD-EBZ | 制造商:Analog Devices 功能描述:DUAL 12-/14-/16-BIT 800 MSPS DAC WITH LOW POWER 32-BIT COMPLEX NCO 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk |
| AD9789BBC | 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| AD9789BBCRL | 制造商:Analog Devices 功能描述:QAM Encoder/Interpolator/Upconverter 164-Pin CSP-BGA T/R 制造商:Analog Devices 功能描述:QAM ENCODER/INTERPOLATOR/UPCNVRTR 164CSPBGA - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 14BIT 2.4GSPS 4CH 164BGA 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14 Bit 2.5 GSPS D-A Converter 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14B 2400MSPS RF w/ 4CH Signal Process 制造商:Analog Devices 功能描述:CONVERTER - DAC |
| AD9789BBCZ | 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。