- 您現在的位置：買賣IC網 > PDF目錄17065 > AD9788-DPG2-EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9788 PDF資料下載
參數資料
| 型號： | AD9788-DPG2-EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/64頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD9788 |
| 設計資源： | Powering the AD9788 Using ADP2105 for Increased Efficiency (CN0141) |
| 標準包裝： | 1 |
| 系列： | * |
| DAC 的數量： | 2 |
| 位數： | 16 |
| 采樣率（每秒）： | 800M |
| 數據接口： | 串行 |
| 設置時間： | 22ms |
| DAC 型： | 電流 |
| 工作溫度： | -40°C ~ 85°C |
| 已供物品： | * |
| 已用 IC / 零件： | AD9788 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
AD9785/AD9787/AD9788
Rev. A | Page 23 of 64
Instruction Byte
The instruction byte contains the following information as
shown in the instruction byte bit map.
Instruction Byte Information Bit Map
MSB
LSB
D7
D6
D5
D4
D3
D2
D1
D0
R/W
X
A4
A3
A2
A1
A0
R/W—Bit 7 of the instruction byte determines whether a read
or write data transfer occurs after the instruction byte write.
Logic 1 indicates a read operation. Logic 0 indicates a write
operation.
X, X —Bit 6 and Bit 5 of the instruction byte are don’t care. In
previous TxDACs, such as the AD9779, these bits define the
number of registers written to or read from in an SPI read/write
operation. In the AD9785/AD9787/AD9788, the register itself
now defines how many bytes are written to or read from.
A4, A3, A2, A1, A0—Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0 of the
instruction byte determine which register is accessed during the
data transfer portion of the communication cycle.
Serial Interface Port Pin Description
SCLK—Serial Clock
The serial clock pin is used to synchronize data to and from the
AD9785/AD9787/AD9788 and to run the internal state machines.
SCLK maximum frequency is 40 MHz.
SPI_CSB—Chip Select
Active low input that allows more than one device on the same
serial communications line. The SPI_SDO and SPI_SDIO pins
go to a high impedance state when this input is high. If driven
high during any communication cycle, that cycle is suspended
until SPI_CSB is reactivated low. Chip select can be tied low in
systems that maintain control of SCLK.
SPI_SDIO—Serial Data I/O
Data is always written into the AD9785/AD9787/AD9788 on
this pin. However, this pin can be used as a bidirectional data
line. Bit 7 of Register 0x00 controls the configuration of this pin.
The default is Logic 0, which configures the SPI_SDIO pin for
input only (4-wire) operation.
SPI_SDO—Serial Data Output
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. In the case where the
AD9785/AD9787/AD9788 operate in a single bidirectional
I/O mode, this pin does not output data and is set to a high
impedance state.
MSB/LSB Transfers
The AD9785/AD9787/AD9788 serial port can support both
most significant bit (MSB) first or least significant bit (LSB)
first data formats. This functionality is controlled by Bit 6 of the
communication (COMM) register. The default value of COMM
Register Bit 6 is low (MSB first). When COMM Register Bit 6 is
set high, the serial port is in LSB first format. The instruction byte
must be written in the format indicated by COMM Register Bit 6.
That is, if the device is in LSB first mode, the instruction byte
must be written from least significant bit to most significant bit.
For MSB first operation, the serial port controller generates the
most significant byte (of the specified register) address first,
followed by the next lesser significant byte addresses until the
I/O operation is complete. All data written to or read from the
AD9785/AD9787/AD9788 must be in MSB first order.
If the LSB mode is active, the serial port controller generates the
least significant byte address first, followed by the next greater
significant byte addresses until the I/O operation is complete.
All data written to or read from the AD9785/AD9787/AD9788
must be in LSB first order.
SPI Resynchronization Capability
If the SPI port becomes unsynchronized at any time, toggling
SCLK for eight or more cycles with SPI_CSB held high resets
the SPI port state machine. The device is then ready for the next
register read or write access.
相關PDF資料 |
PDF描述 |
|---|---|
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
| EMA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| EVAL-AD5392EBZ | BOARD EVAL FOR AD5392 |
| 380LX682M025H022 | CAP ALUM 6800UF 25V 20% SNAP |
| DC941A | BOARD DELTA SIGMA ADC LTC2482 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9788-EBZ | 制造商:Analog Devices 功能描述:Evaluation Board For AD9788 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk 制造商:Analog Devices 功能描述:Digital to Analog Eval. Board |
| AD9788MOD-EBZ | 制造商:Analog Devices 功能描述:DUAL 12-/14-/16-BIT 800 MSPS DAC WITH LOW POWER 32-BIT COMPLEX NCO 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk |
| AD9789BBC | 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| AD9789BBCRL | 制造商:Analog Devices 功能描述:QAM Encoder/Interpolator/Upconverter 164-Pin CSP-BGA T/R 制造商:Analog Devices 功能描述:QAM ENCODER/INTERPOLATOR/UPCNVRTR 164CSPBGA - Tape and Reel 制造商:Analog Devices 功能描述:IC DAC 14BIT 2.4GSPS 4CH 164BGA 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14 Bit 2.5 GSPS D-A Converter 制造商:Analog Devices Inc. 功能描述:Digital to Analog Converters - DAC 14B 2400MSPS RF w/ 4CH Signal Process 制造商:Analog Devices 功能描述:CONVERTER - DAC |
| AD9789BBCZ | 功能描述:數模轉換器- DAC 14 Bit 2.5 GSPS D-A Converter RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。