- 您現在的位置：買賣IC網 > PDF目錄10561 > XRT83VSH38IB-F (Exar Corporation)IC LIU SH T1/E1/J1 8CH 225BGA PDF資料下載
參數資料
| 型號： | XRT83VSH38IB-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 62/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU SH T1/E1/J1 8CH 225BGA |
| 標準包裝： | 84 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 8/8 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 225-BGA |
| 供應商設備封裝： | 225-BGA（19x19） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1484 XRT83VSH38IB-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
XRT83VSH38
62
REV. 1.1.0
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
CLOCK SELECT REGISTER
The input clock source is used to generate all the necessary clock references internally to the LIU. The
microprocessor timing is derived from a PLL output which is chosen by programming the Clock Select Bits and
the Master Clock Rate in register 0x81h. Therefore, if the clock selection bits or the MCLRATE bit are being
programmed, the frequency of the PLL output will be adjusted accordingly.
During this adjustment, it is
important to "Not" write to any other bit location within the same register while selecting the input/output clock
frequency. For best results, register 0x81h can be broken down into two sub-registers with the MSB being bits
D[7:3] and the LSB being bits D[2:0] as shown in Figure 37. Note: Bit D[7] is a reserved bit.
FIGURE 37. REGISTER 0X81H SUB REGISTERS
Programming Examples:
Example 1: Changing bits D[7:3]
If bits D[7:3] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 2: Changing bits D[2:0]
If bits D[2:0] are the only values within the register that will change in a WRITE process, the microprocessor
only needs to initiate ONE write operation.
Example 3: Changing bits within the MSB and LSB
In this scenario, one must initiate TWO write operations such that the MSB and LSB do not change within ONE
write cycle. It is recommended that the MSB and LSB be treated as two independent sub-registers. One can
either change the clock selection (MSB) and then change bits D[2:0] (LSB) on the SECOND write, or vice-
versa. No order or sequence is necessary.
D0
D1
D2
D3
D4
D5
D6
D7
MSB
LSB
Clock Selection Bits
ExLOS, ICT
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BT4-MX-F1 | CONVERTER MOD DC/DC 48V 75W |
| SP508CF-L | IC TXRX MULTIPROTOCOL 100LQFP |
| VI-BT4-MW | CONVERTER MOD DC/DC 48V 100W |
| SF6382-6SG-520 | CONN PLUG 6POS CABLE SKT |
| VI-BT3-MX-F3 | CONVERTER MOD DC/DC 24V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83VSH38IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT84L38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER |
| XRT84L38_06 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER |
| XRT84L38IB | 功能描述:網絡控制器與處理器 IC 8 Ch T1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT84L38-L38PCI | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。