- 您現在的位置：買賣IC網 > PDF目錄10561 > XRT83VSH38IB-F (Exar Corporation)IC LIU SH T1/E1/J1 8CH 225BGA PDF資料下載
參數資料
| 型號： | XRT83VSH38IB-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 38/76頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU SH T1/E1/J1 8CH 225BGA |
| 標準包裝： | 84 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 8/8 |
| 規程： | T1，E1，J1 |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 225-BGA |
| 供應商設備封裝： | 225-BGA（19x19） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1484 XRT83VSH38IB-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
XRT83VSH38
40
REV. 1.0.9
8-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
6.1.2
24-Bit Serial Data Input Descritption
The serial data input is sampled on the rising edge of SCLK. In readback mode, the serial data output is
updated on the falling edge of SCLK. The serial data must be applied to the LIU LSB first. The 24 bits of serial
data are described below.
6.1.3
ADDR[7:0] (SCLK1 - SCLK8)
The first 8 SCLK cycles are used to provide the address to which a Read or Write operation will occur.
ADDR[0] (LSB) must be sent to the LIU first followed by ADDR[1] and so forth until all 8 address bits have been
sampled by SCLK.
6.1.4
R/W (SCLK9)
The next serial bit applied to the LIU informs the microprocessor that a Read or Write operation is desired. If
the R/W bit is set to “0”, the microprocessor is configured for a Write operation. If the R/W bit is set to “1”, the
microprocessor is configured for a Read operation.
6.1.5
Dummy Bits (SCLK10 - SCLK16)
The next 7 SCLK cycles are used as dummy bits. Seven bits were chosen so that the serial interface can
easily be divided into three 8-bit words to be compliant with standard serial interface devices. The state of
these bits are ignored and can hold either “0” or “1” during both Read and Write operations.
6.1.6
DATA[7:0] (SCLK17 - SCLK24)
The next 8 SCLK cycles are used to provide the data to be written into the internal register chosen by the
address bits. DATA[0] (LSB) must be sent to the LIU first followed by DATA[1] and so forth until all 8 data bits
have been sampled by SCLK. Once 24 SCLK cycles have been completed, the LIU holds the data until CS is
pulled “High” whereby, the serial microprocessor latches the data into the selected internal register.
6.1.7
8-Bit Serial Data Output Description
The serial data output is updated on the falling edge of SCLK17 - SCLK24 if R/W is set to “1”. DATA[0] (LSB)
is provided on SCLK17 to the SDO pin first followed by DATA[1] and so forth until all 8 data bits have been
updated. The SDO pin allows the user to read the contents stored in individual registers by providing the
desired address on the SDI pin during the Read cycle.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BT4-MX-F1 | CONVERTER MOD DC/DC 48V 75W |
| SP508CF-L | IC TXRX MULTIPROTOCOL 100LQFP |
| VI-BT4-MW | CONVERTER MOD DC/DC 48V 100W |
| SF6382-6SG-520 | CONN PLUG 6POS CABLE SKT |
| VI-BT3-MX-F3 | CONVERTER MOD DC/DC 24V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XRT83VSH38IB-F | 制造商:Exar Corporation 功能描述:T1/E1 LIU IC |
| XRT84L38 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER |
| XRT84L38_06 | 制造商:EXAR 制造商全稱:EXAR 功能描述:OCTAL T1/E1/J1 FRAMER |
| XRT84L38IB | 功能描述:網絡控制器與處理器 IC 8 Ch T1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| XRT84L38-L38PCI | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。