- 您現在的位置：買賣IC網 > PDF目錄1975 > XR17V354IB176-F (Exar Corporation)IC UART PCIE 256B QUAD 176FPBGA PDF資料下載
參數資料
| 型號： | XR17V354IB176-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 50/66頁 |
| 文件大小： | 0K |
| 描述： | IC UART PCIE 256B QUAD 176FPBGA |
| 產品培訓模塊： | PCIe UARTs |
| 標準包裝： | 160 |
| 特點： | * |
| 通道數： | 4，QUART |
| FIFO's： | 256 字節 |
| 規程： | RS485 |
| 電源電壓： | 3.3V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 176-LFBGA |
| 供應商設備封裝： | 176-FPBGA（13x13） |
| 包裝： | 托盤 |
| 其它名稱： | 1016-1472 XR17V354IB176-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁當前第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
XR17V354
54
HIGH PERFORMANCE QUAD PCI-EXPRESS UART
REV. 1.0.3
MCR[2]: DTR# or RTS# for Auto Flow Control (OP1 in Local Loopback Mode)
DTR# or RTS# auto hardware flow control select. This bit is in effect only when auto RTS/DTR is enabled by
EFR bit [6]. DTR# selection is associated with DSR# and RTS# is with CTS#.
Logic 0 = Uses RTS# and CTS# pins for auto hardware flow control.
Logic 1 = Uses DTR# and DSR# pins for auto hardware flow control.
In Local Loopback mode (MCR[4] = 1), this bit acts as the legacy OP1 output and controls the RI bit in the MSR
register, as shown in Figure 12.
MCR[1]: RTS# Output
The RTS# pin may be used for automatic hardware flow control by enabled by EFR bit [6] and MCR bit [2]=0. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force RTS# output to a HIGH (default).
Logic 1= Force RTS# output to LOW.
MCR[0]: DTR# Output
The DTR# pin may be used for automatic hardware flow control enabled by EFR bit [6] and MCR bit [2]=1. If
the modem interface is not used, this output may be used for general purpose.
Logic 0 = Force DTR# output to a HIGH (default).
Logic 1 = Force DTR# output to a LOW.
4.9
Line Status Register (LSR) - Read Only
This register provides the status of data transfers between the UART and the host. If IER bit [2] is set to a
logic 1, an LSR interrupt will be generated immediately when any character in the RX FIFO has an error (parity,
framing, overrun, break).
LSR[7]: Receive FIFO Data Error Flag
Logic 0 = No FIFO error (default).
Logic 1 = An indicator for the sum of all error bits in the RX FIFO. At least one parity error, framing error or
break indication is in the FIFO data. This bit clears when there are no more errors in the FIFO.
LSR[6]: Transmitter Empty Flag
This bit is the Transmitter Empty indicator. This bit is set to a logic 1 whenever both the transmit FIFO (or THR,
in non-FIFO mode) and the transmit shift register (TSR) are both empty. It is set to logic 0 whenever either the
TX FIFO or TSR contains a data character.
LSR[5]: Transmit FIFO Empty Flag
This bit is the Transmit FIFO Empty indicator. This bit indicates that the transmitter is ready to accept a new
character for transmission. This bit is set to a logic HIGH when the last data byte is transferred from the
transmit FIFO to the transmit shift register. The bit is reset to logic 0 as soon as a data byte is loaded into the
transmit FIFO. In the non-FIFO mode this bit is set when the transmit holding register (THR) is empty; it is
cleared when at a byte is written to the THR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was LOW for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO. The break indication remains until the RX input
returns to the idle condition, “mark” or HIGH.
相關PDF資料 |
PDF描述 |
|---|---|
| XR17V358IB176-F | IC UART PCIE OCTAL 176FPBGA |
| XR19L200IL32-F | IC UART/TXRX RS232 32QFN |
| XR19L202IL48-F | IC UART/TXRX RS232 48QFN |
| XR19L210IL40-F | IC UART/TXRX RS232 40QFN |
| XR19L212IL48-F | IC UART/TXRX RS232 48QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XR17V354IB-E4-EVB | 功能描述:界面開發工具 Eval Board for XR17V354IB-E4 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17V354IB-E8-EVB | 功能描述:界面開發工具 Eval Board for XR17V354IB-E8 RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17V358 | 制造商:EXAR 制造商全稱:EXAR 功能描述:HIGH PERFORMANCE OCTAL PCI EXPRESS UART |
| XR17V358IB-0A-EVB | 功能描述:界面開發工具 Eval Board for XR17V358IB-0A RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| XR17V358IB176-F | 功能描述:UART 接口集成電路 8 Channel PCIe UART w/256 Byte FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。