參數資料
型號： UPD17240MC-XXX-5A4-A
元件分類： 微控制器/微處理器
英文描述： 4-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO30
封裝： 0.300 INCH, PLASTIC, SSOP-30
文件頁數： 29/102頁
文件大?。?/td> 668K
代理商： UPD17240MC-XXX-5A4-A
32
Data Sheet U15002EJ1V0DS
PD17240, 17241, 17242, 17243, 17244, 17245, 17246
2.5.2
Control registers
The control registers consist of a total of 64 nibbles (64
× 4 bits) of addresses 00H to 3FH of the register file.
Of these, however, only 24 nibbles are actually used. The remaining 40 nibbles are unused registers that are
prohibited from being read or written.
When the “PEEK WR, rf” instruction is executed, the contents of the register file addressed by “rf” are read to the
window register.
When the “POKE rf, WR” instruction is executed, the contents of the window register are written to the register
file addressed by “rf”.
When using the assembler (RA17K), the macro instructions listed below, which are embedded as flag type symbol
manipulation instructions, can be used. The macro instructions allow the contents of the register file to be manipulated
in bit units.
For the configuration of the control register, refer to Figure 12-1 Register File List.
SETn:
Sets flag to “1”
CLRn:
Sets flag to “0”
SKTn:
Skips if all flags are “1”
SKFn:
Skips if all flags are “0”
NOTn:
Inverts flag
INITFLG:
Initializes flag
INITFLGX: Initializes flag
2.5.3
Notes on using register files
When using the register files, bear in mind the points described below. For details, refer to the
PD172xx
Subseries User’s Manual (U12795E).
(1) When manipulating control registers (read-only and unused registers)
When manipulating the write-only (W), the read-only (R), and unused control registers by using an assembler
or in-circuit emulator, keep in mind the following points.
When device operates
Nothing changes even if data is written to a read-only register.
If an unused register is read, an undefined value is read; nothing is changed even if data is written to this
register.
Using assembler
An error occurs if an instruction is executed to read data from a write-only register.
An error occurs if an instruction is executed to write data to a read-only register.
An error also occurs if an instruction is executed to read or write an unused address.
When an in-circuit emulator (IE-17K or IE-17K-ET) is used (when an instruction is executed for patch
processing)
An undefined value is read if a write-only register is read, and an error does not occur.
Nothing changes even if data is written to a read-only register, and an error does not occur.
An undefined value is read if an unused address is read; nothing changes even if data is written to this
address. An error does not occur.
相關PDF資料
PDF描述
UPD17242UC-XXX-5A4 4-BIT, MROM, 4.5 MHz, MICROCONTROLLER, PDSO30
UPD178F054 78K/0 Series for Instructions | User＇s Manual[10/2001]
UPD178F124 78K/0 Series for Instructions | User＇s Manual[10/2001]
UPD178F098GF-3BA-A 8-BIT, FLASH, MICROCONTROLLER, PQFP100
UPD17P136BGT MICROCONTROLLER, PDSO28
相關代理商/技術參數
參數描述
UPD17241 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17241MC-XXX-5A4 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17242 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17242MC-XXX-5A4 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
UPD17243 制造商:NEC 制造商全稱:NEC 功能描述:4-BIT SINGLE-CHIP MICROCONTROLLERS FOR SMALL GENERAL-PURPOSE INFRARED REMOTE CONTROL TRANSMITTERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*