- 您現在的位置：買賣IC網 > PDF目錄385869 > ST6240B (意法半導體) Replaced by PT6302 : 5Vout 3A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 70 PDF資料下載
參數資料
| 型號： | ST6240B |
| 廠商： | 意法半導體 |
| 英文描述： | Replaced by PT6302 : 5Vout 3A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 70 |
| 中文描述： | 8位檢察官辦公室/存儲器與LCD驅動器，EEPROM和一個微處理器/ D轉換器 |
| 文件頁數： | 45/76頁 |
| 文件大小： | 1280K |
| 代理商： | ST6240B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁當前第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
45/76
ST62T40B/E40B
A/D CONVERTER
(Cont’d)
Since the ADC is on the same chip as the micro-
processor, the user should not switch heavily load-
ed output signals during conversion, if high preci-
sion is required. Such switching will affect the sup-
ply voltages used as analog references.
The accuracy of the conversion depends on the
quality of the power supplies (V
DD
and V
SS
). The
user must take special care to ensure a well regu-
lated reference voltage is present on the V
DD
and
V
SS
pins (power supply voltage variations must be
less than 5V/ms). This implies, in particular, that a
suitable decoupling capacitor is used at the V
DD
pin.
The converter resolution is given by::
The Input voltage (Ain) which is to be converted
must be constant for 1μs before conversion and
remain constant during conversion.
Conversion resolution can be improved if the pow-
er supply voltage (V
DD
) to the microcontroller is
lowered.
In order to optimise conversion resolution, the user
can configure the microcontroller in WAIT mode,
because this mode minimises noise disturbances
and power supply variations due to output switch-
ing. Nevertheless, the WAIT instruction should be
executed as soon as possible after the beginning
of the conversion, because execution of the WAIT
instruction may cause a small variation of the V
DD
voltage. The negative effect of this variation is min-
imized at the beginning of the conversion when the
converter is less sensitive, rather than at the end
of conversion, when the less significant bits are
determined.
The best configuration, from an accuracy stand-
point, is WAIT mode with the Timer stopped. In-
deed, only the ADC peripheral and the oscillator
are then still working. The MCU must be woken up
from WAIT mode by the ADC interrupt at the end
of the conversion. It should be noted that waking
up the microcontroller could also be done using
the Timer interrupt, but in this case the Timer will
be working and the resulting noise could affect
conversion accuracy.
A/D Converter Control Register (ADCR)
Address: 0D1h
—
Read/Write
Bit 7 =
EAI
: Enable A/D Interrupt.
If this bit is set to
“1” the A/D interrupt is enabled, when EAI=0 the
interrupt is disabled.
Bit 6 =
EOC
: End of conversion.Read Only. This
read only bit indicates when a conversion has
been completed. This bit is automatically reset to
“0” when the STA bit is written. If the user is using
the interrupt option then this bit can be used as an
interrupt pending bit. Data in the data conversion
register are valid only when this bit is set to “1”.
Bit 5 =
STA
: Start of Conversion. Write Only Writ-
ing a “1” to this bit will start a conversion on the se-
lected channel and automatically reset to “0” the
EOC bit. If the bit is set again when a conversion is
in progress, the present conversion is stopped and
a new one will take place. This bit is write only, any
attempt to read it will show a logical zero.
Bit 4 =
PDS
: Power Down Selection. This bit acti-
vates the A/D converter if set to “1”. Writing a “0” to
this bit will put the ADC in power down mode (idle
mode).
Bit 3-0 =
D3-D0.
Not used
A/D Converter Data Register (ADR)
Address: 0D0h
—
Read only
Bit 7-0 =
D7-D0
: 8 Bit A/D Conversion Result.
V
---------------------------
V
–
256
7
0
EAI
EOC
STA
PDS
D3
D2
D1
D0
7
0
D7
D6
D5
D4
D3
D2
D1
D0
617
相關PDF資料 |
PDF描述 |
|---|---|
| ST62E18C | 16-Bit Registered Transceivers With 3-State Outputs 56-SSOP -40 to 85 |
| ST62T18C | 8-BIT MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, UART, OSG, SAFE RESET AND 20-PIN PACKAGE |
| ST62E40B | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST62T40B | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST62T10 | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST6240B-EMU2 | 功能描述:仿真器/模擬器 ST62 Emulator Board RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2 |
| ST6240BQ1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. LCD DRIVER. EEPROM. A/D CONVERTER AND 80 PINS |
| ST6240BQ1/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| ST6240BQ6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. LCD DRIVER. EEPROM. A/D CONVERTER AND 80 PINS |
| ST6240BQ6/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。