- 您現在的位置：買賣IC網 > PDF目錄385869 > ST6240B (意法半導體) Replaced by PT6302 : 5Vout 3A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 70 PDF資料下載
參數資料
| 型號： | ST6240B |
| 廠商： | 意法半導體 |
| 英文描述： | Replaced by PT6302 : 5Vout 3A Wide Input Positive Step-Down ISR 3-SIP MODULE -40 to 70 |
| 中文描述： | 8位檢察官辦公室/存儲器與LCD驅動器，EEPROM和一個微處理器/ D轉換器 |
| 文件頁數： | 21/76頁 |
| 文件大小： | 1280K |
| 代理商： | ST6240B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
21/76
ST62T40B/E40B
RESETS
(Cont’d)
3.2.3 Watchdog Reset
The MCU provides a Watchdog timer function in
order to ensure graceful recovery from software
upsets. If the Watchdog register is not refreshed
before an end-of-count condition is reached, the
internal reset will be activated. This, amongst oth-
er things, resets the watchdog counter.
The MCU restarts just as though the Reset had
been generated by the RESET pin, including the
built-in stabilisation delay period.
3.2.4 Application Notes
No external resistor is required between V
DD
and
the Reset pin, thanks to the built-in pull-up device.
The POR circuit operates dynamically, in that it
triggers MCU initialization on detecting the rising
edge of V
DD
. The typical threshold is in the region
of 2 volts, but the actual value of the detected
threshold depends on the way in which V
DD
rises.
The POR circuit is NOTdesigned to supervise
static, or slowly rising or falling V
DD
.
3.2.5 MCU Initialization Sequence
When a reset occurs the stack is reset, the PC is
loaded with the address of the Reset Vector (locat-
ed in program ROM starting at address 0FFEh). A
jump to the beginning of the user program must be
coded at this address. Following a Reset, the In-
terrupt flag is automatically set, so that the CPU is
in Non Maskable Interrupt mode; this prevents the
initialisation routine from being interrupted. The in-
itialisation routine should therefore be terminated
by a RETI instruction, in order to revert to normal
mode and enable interrupts. If no pending interrupt
is present at the end of the initialisation routine, the
MCU will continue by processing the instruction
immediately following the RETI instruction. If, how-
ever, a pending interrupt is present, it will be serv-
iced.
Figure 12Reset and Interrupt Processing
Figure 13Reset Block Diagram
RESET
RESET
VECTOR
JP
JP:2 BYTES/4 CYCLES
RETI
RETI: 1 BYTE/2 CYCLES
INITIALIZATION
ROUTINE
VA00181
V
DD
RESET
300k
2.8k
POWER
WATCHDOG RESET
CK
COUNTER
RESET
ST6
INTERNAL
RESET
f
OSC
RESET
ON RESET
VA0200B
593
相關PDF資料 |
PDF描述 |
|---|---|
| ST62E18C | 16-Bit Registered Transceivers With 3-State Outputs 56-SSOP -40 to 85 |
| ST62T18C | 8-BIT MCUs WITH A/D CONVERTER, AUTO-RELOAD TIMER, UART, OSG, SAFE RESET AND 20-PIN PACKAGE |
| ST62E40B | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST62T40B | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| ST62T10 | 8-BIT OTP/EPROM MCUs WITH A/D CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST6240B-EMU2 | 功能描述:仿真器/模擬器 ST62 Emulator Board RoHS:否 制造商:Blackhawk 產品:System Trace Emulators 工具用于評估:C6000, C5000, C2000, OMAP, DAVINCI, SITARA, TMS470, TMS570, ARM 7/9, ARM Cortex A8/R4/M3 用于:XDS560v2 |
| ST6240BQ1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. LCD DRIVER. EEPROM. A/D CONVERTER AND 80 PINS |
| ST6240BQ1/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| ST6240BQ6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER ( MCU ) WITH OTP. ROM. FASTROM. EPROM. LCD DRIVER. EEPROM. A/D CONVERTER AND 80 PINS |
| ST6240BQ6/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。